Product Knowledge

Do Self-Undercutting Anchors Need Special Drill Bits? Installation Tool Selection and Operating Essentials Explained

Views: 0Posted on: 2026-10-14

First, the conclusion:Self-undercutting anchorsrequire dedicated installation tools, but do not require a separate secondary reaming operation as do undercut anchors. The reaming and installation of a self-undercutting anchor (also called a self-cutting anchor) are completed simultaneously — the anchor's expansion element carries a hard cutting edge (diamond or tungsten carbide); during installation, the installation rod on the rotary hammer engages with the slot on the anchor's expansion sleeve, and reaming and expansion-element embedment are completed while rotating and hammering. Therefore, The straight hole of a self-undercutting anchor can be drilled with a standard-size ordinary rotary hammer drill bit, but installation must use Daring's supplied dedicated hammer-in sleeve, which cannot be replaced by ordinary tools. Daring supplies dedicated hammer-in sleeves with square and round shanks; once the sleeve is connected to the hammer drill and fitted over the anchor rod, the anchor can be installed quickly with the hammer drill. A complete self-undercutting anchor installation tool set should include: a rotary hammer, a straight-hole drill bit, a dust blower (or air pump), a dedicated hammer-in sleeve, and a torque wrench (if torque tightening is used). Daring self-undercutting anchors offer pull-out force of over 50 kN, provide immediate seating with no curing, and are available in grade 5.8/8.8 carbon steel and 304/316 stainless steel.

Scope of application:This article applies to the selection of installation tools and operating guidance for self-undercutting anchors in concrete substrates. Undercut anchors (form-undercut anchors) require a dedicated undercutting drill bit for secondary reaming; their tool configuration differs from that described here — see the Daring guide to installation tools for undercut anchors.

Self-undercutting anchors are increasingly used in curtain walls, equipment installation, rail transit and other projects because they are convenient to install and eliminate the secondary reaming step. However, many construction workers hold two extreme misconceptions about tool selection: one is that "self-undercutting means no dedicated tools are needed and an ordinary impact driver will do"; the other is that "a dedicated undercutting drill bit is required for installation". Neither is correct. Starting from the reaming principle of self-undercutting anchors, this article systematically explains the key points of tool selection and the standardized operating procedure.

I. The Reaming Principle of Self-Undercutting Anchors — Why Secondary Reaming Is Not Required

1.1 Core Difference Between Self-Undercutting and Undercut Anchors

Installing an undercut anchor (form-undercut anchor) involves two steps: first drill a straight hole with an impact drill, then use a dedicated undercutting drill bit to ream the bottom of the hole, forming a wedge-shaped hole that is wider at the bottom and narrower at the top, and then insert the anchor. A self-undercutting anchor works quite differently — its expansion element carries a hard cutting edge; during installation, the installation rod on the rotary hammer engages with the slot on the anchor's expansion sleeve, and reaming and expansion-element embedment are completed simultaneously while rotating and hammering, with no separate reaming required. The difference in construction method determines the difference in tool configuration: undercut anchors must be fitted with a dedicated undercutting drill bit, while self-undercutting anchors do not need one.

1.2 Synchronized Reaming and Installation Mechanism of Self-Undercutting Anchors

Daring self-undercutting anchors use a twin-cutter design, allowing the twin cutters to cut into the straight hole more quickly; the entire one-step installation completes the reaming, with no separate reaming required, substantially reducing working hours. During installation, connect the dedicated hammer-in sleeve to the hammer drill, fit it over the anchor rod, and the rotary hammering force is transmitted through the sleeve to the cutter at the bottom of the anchor; the cutter cuts the concrete to form an undercut cavity, while the expansion segments open and embed into the cavity, forming a mechanical key. The whole process — "rotating, cutting the undercut and seating at the same time" — is completed in one step.

II. List of Installation Tools for Self-Undercutting Anchors

2.1 Four Core Tools

According to the installation procedure for Daring self-undercutting anchors, the following four categories of tools are required on site:

Tool namePurposeDaring supply statusRemarks
Rotary hammer / demolition hammerDrilling and rotary-hammer installationProvided by the contractorMust have both rotation and hammering functions
Straight-hole drill bitDrilling straight holes (no reaming required)Provided by the contractor or purchased through DaringA standard-size ordinary rotary hammer drill bit is sufficient
Dust blower / air pumpCleaning the hole, blowing out dustProvided by the contractorHole cleaning for self-undercutting anchors is relatively simple
Dedicated hammer-in sleeveConnects the hammer drill to the anchor and transmits the rotary hammering forceSupplied by DaringAvailable with square shank and round shank

Installation requires four tools: a rotary hammer, a straight-hole drill bit, a dust blower and a hammer-in sleeve; the manufacturer supplies the hammer-in sleeve, while the others may need to be selected and purchased separately.

2.2 Key Role of the Dedicated Hammer-In Sleeve

The dedicated hammer-in sleeve is the most critical and irreplaceable component. Daring supplies dedicated hammer-in sleeves with square and round shanks; once the sleeve is connected to the hammer drill and fitted over the anchor rod, the anchor can be installed quickly. The sleeve's role is not only to transmit the hammering force, but more importantly to ensure that the rotary hammering force is transmitted uniformly to the cutting cutter at the bottom of the anchor, so that the cutter cuts the concrete at the correct angle and with the correct force. Substituting an ordinary socket or wrench results in uneven transmission of the cutting force, so the cutter cannot effectively cut into the concrete and the undercutting effect is greatly reduced.

2.3 Straight-Hole Drill Bit — Ordinary Drill Bits Can Be Used

Unlike undercut anchors, the straight-hole drilling of self-undercutting anchors can use a standard-size ordinary rotary hammer drill bit. Because the reaming of a self-undercutting anchor is performed by the anchor's own cutter, the straight-hole stage does not need to form an undercut cavity — it is sufficient to drill a cylindrical hole meeting the diameter and depth requirements. However, note that the diameter of the straight-hole drill bit must strictly match the anchor specification, and the drilling depth must also comply with the product parameter table. Using a mismatched drill bit to "save trouble" is strictly prohibited, as it will prevent correct seating of the anchor or result in insufficient undercutting.

III. Standardized Installation Procedure for Self-Undercutting Anchors

3.1 Step 1: Drilling

Using a rotary hammer with a straight-hole drill bit matched to the anchor specification, drill into the concrete substrate to the specified depth. Keep the drill bit vertical during drilling to ensure smooth hole walls. The drilling depth shall equal the effective embedment depth, with deviation controlled within +5 mm.

3.2 Step 2: Hole Cleaning

Aim the dust blower at the hole and blow out dust until no dust emerges from the hole. Hole cleaning for self-undercutting anchors is relatively simple: it is sufficient to blow the dust out of the hole wall, with no need for a second cleaning with a brush. However, if water has accumulated in the hole, remove it with absorbent cotton strips or a vacuum pump before installation.

3.3 Step 3: Hammer Installation

Connect the dedicated hammer-in sleeve to the hammer drill, fit it over the anchor rod, start the hammer drill's rotation + hammering mode, and hammer the self-undercutting anchor sleeve downward so that the bottom cutter cuts the concrete to form an undercut cavity, while the expansion segments open and embed into the cavity, completing the mechanical lock. During installation, judge whether the anchor is correctly seated by visual observation of displacement: if correctly seated, the top of the sleeve should be 1 mm to 3 mm below the concrete surface.

3.4 Step 4: Torque Tightening (if applicable)

Some self-undercutting anchor models also require a calibrated torque wrench to apply the specified torque to the nut after hammer installation, so as to ensure precise expansion and tightening of the locking parts. When tightening the anchor with a torque wrench, the anchor head gradually expands under the axial force of the wrench, and the self-cutting key begins to undercut; when the anchor body reaches the specified axial displacement, the cavity reaming is complete and the middle self-locking part expands, creating a self-locking effect. Installation is complete when the torque wrench reaches the design value.

IV. Common Misconceptions and Key Operating Points

4.1 Misconception 1: Replacing the Dedicated Hammer-In Sleeve with an Ordinary Socket

This is the most common error. The inner wall of the dedicated hammer-in sleeve is precisely matched to the slots of the anchor rod and sleeve, enabling the rotary hammering force to be transmitted uniformly to the bottom cutter. Using an ordinary socket or hammering directly on the top of the anchor results in uneven transmission of the cutting force, so the cutter cannot effectively cut into the concrete; the undercutting effect is greatly reduced and the cutter may even chip.

4.2 Misconception 2: Believing That Self-Undercutting Anchors Can Be Installed with Any Rotary Hammer

Installation of self-undercutting anchors requires a rotary hammer with both rotation and hammering functions, and the impact energy and rotational speed must meet the product installation requirements. An underpowered rotary hammer cannot provide sufficient cutting force, so the cutter cannot effectively cut into the concrete and undercutting is insufficient. A SDS-plus or SDS-max rotary hammer matched to the anchor specification is recommended to ensure that impact energy and speed meet the requirements of the product manual.

4.3 Misconception 3: Ignoring the Check for Correct Installation Depth

Judge whether the anchor is correctly seated by visual observation of displacement during installation. If the top of the sleeve is flush with or above the concrete surface, the anchor is not correctly seated and the undercut is insufficient. If the top of the sleeve is 1 mm to 3 mm below the concrete surface, the anchor is correctly seated. Daring self-undercutting anchors carry installation marks on the rod, allowing construction personnel to judge correct seating by visually checking the position of the mark.

4.4 Misconception 4: Brute-Force Installation

Undercut anchors are most vulnerable to brute-force installation (hammering the anchor with maximum force without reaming), whereas self-undercutting anchors are not affected even by brute-force installation. This does not mean, however, that the hammering force can be increased arbitrarily. Excessive hammering force may cause local cracking of the concrete substrate or damage to the anchor cutter; installation shall be carried out in accordance with the operating parameters specified in the product manual.

V. Daring Self-Undercutting Anchor Product Parameters

5.1 Specifications and Materials

ItemDaring self-undercutting anchor parameter
Materialgrade 5.8 carbon steel, grade 8.8 carbon steel, 304 stainless steel, 316 stainless steel
Surface treatment (carbon steel)Electro-zinc plating, hot-dip galvanizing
Specifications / modelsM10×60×100、M12×80×130、M12×100×150、M16×100×160、M16×125×190
Pull-out forceup to over 50 kN
Applicable base materialcracked / uncracked concrete C20–C60

Daring self-undercutting anchors use a twin-cutter design with integrated cutting and reaming installation, requiring no separate reaming and substantially reducing working hours. Dedicated square-shank and round-shank hammer-in sleeves are supplied with the product and can be used once connected to the hammer drill.

5.2 Application Scenarios for Self-Undercutting Anchors

  • Conventional curtain-wall projects: convenient construction with no secondary reaming required, effectively improving construction efficiency.

  • Equipment foundation anchoring: load carried by mechanical locking, with excellent vibration and fatigue resistance.

  • Rail transit: suitable for anchoring applications such as electromechanical supports and evacuation platforms in tunnels.

  • Large-size requirements: self-undercutting anchors are available up to M20, while undercut anchors generally only go up to M16; self-undercutting is preferred for large-size applications.

VI. Frequently Asked Questions

Q1Do self-undercutting anchors require a dedicated drill bit?
The straight hole of a self-undercutting anchor can be drilled with a standard-size ordinary rotary hammer drill bit; unlike undercut anchors, no dedicated undercutting drill bit is required. This is because reaming is performed simultaneously by the anchor's own cutter during installation, so the straight-hole stage only needs a cylindrical hole meeting the diameter and depth requirements. However, installation must use Daring's supplied dedicated hammer-in sleeve.
Q2What tools are required to install self-undercutting anchors?
Four types of tools are required: a rotary hammer (with both rotation and hammering functions), a straight-hole drill bit matched to the anchor specification, a dust blower/air pump (for hole cleaning), and a dedicated hammer-in sleeve (supplied by Daring, available with square or round shank). Some models also require a torque wrench for torque tightening.
Q3Can self-undercutting anchors be installed with an ordinary socket?
No. The inner wall of the dedicated hammer-in sleeve is precisely matched to the slots of the anchor rod and sleeve, enabling uniform transmission of the hammer drill's rotary hammering force to the bottom cutter. Using an ordinary socket results in uneven transmission of the cutting force, so the cutter cannot effectively cut into the concrete and the undercutting effect is greatly reduced.
Q4How can correct installation of a self-undercutting anchor be determined?
During installation, judge by visual observation of displacement: if the top of the sleeve is 1 mm to 3 mm below the concrete surface, the anchor is correctly seated. Daring self-undercutting anchors carry installation marks on the rod, allowing construction personnel to judge correct seating by visually checking the position of the mark.
Q5What is the difference in tool configuration between self-undercutting and undercut anchors?
Undercut anchors require a dedicated undercutting drill bit for secondary reaming and have a more complex tool configuration; the straight hole of a self-undercutting anchor can be drilled with an ordinary rotary hammer drill bit and does not require a dedicated undercutting drill bit, but the installation step must use a dedicated hammer-in sleeve. Self-undercutting anchors are more convenient to install and take less working time.
Q6What specifications and materials are available for Daring self-undercutting anchors?
Daring self-undercutting anchors are available in grade 5.8 carbon steel, grade 8.8 carbon steel and 304/316 stainless steel, with surface treatments including electro-zinc plating and hot-dip galvanizing. Model specifications include M10×60×100, M12×80×130, M12×100×150, M16×100×160 and M16×125×190. Pull-out force can reach over 50 kN, and they are suitable for cracked/uncracked concrete substrates C20–C60.

Daring self-undercutting anchors use a twin-cutter design with integrated cutting and reaming installation, requiring no separate reaming and supplied with dedicated square-shank and round-shank hammer-in sleeves that can be used once connected to a hammer drill. With pull-out force reaching over 50 kN, they perform better under high loads, vibration and impact, require no curing time, and effectively improve construction efficiency. The Daring mechanical anchor range covers undercut, self-undercutting, drop-in, Anka and heavy-duty mechanical anchors, made of carbon steel/stainless steel with multiple coating options; mechanical locking provides immediate seating with no curing required. For guidance on selecting self-undercutting anchors and installation techniques for specific projects, please consult the Daring technical team.

References

JGJ 145-2013, Technical Specification for Post-Installed Anchorage in Concrete Structures — anchor installation tools and construction requirements

JG/T 160-2017, Mechanical Anchors for Concrete — classification and technical requirements for mechanical anchors

GB 50367-2013, Code for Design of Strengthening Concrete Structures — anchor selection requirements for load-bearing structures

Daring website — How to choose undercut anchor installation tools? Differences between dedicated undercutting drill bits and ordinary drill bits explained

Daring website — What is the difference between undercut anchors and self-undercutting anchors? A clear guide to choosing

Daring website — How to use self-undercutting mechanical anchors (with illustrations)

Daring website — Self-undercutting anchor product parameters

Daring website — Mechanical anchor product series

Back to Daring Home  Back to Top