| [Compliance and Technical Notice]According to JGJ 145-2013 Technical Specification for Post-Installed Anchoring in Concrete Structures and GB 50367-2013 Design Code for Strengthening Concrete Structures, undercut mechanical anchors are highly reliable mechanically interlocked components whose mechanical performance depends entirely on the geometric accuracy of the reverse-cone cavity formed within the base material.It is strictly prohibited to use ordinary straight-hole drill bits with manual techniques such as “wobble drilling” or “sway drilling” in place of dedicated undercut drill bits to form the hole.Connection nodes undercut without complete dedicated tooling per the specified workmanship are deemed invalid anchorage and cannot pass seismic and pull-out acceptance. |
The bottom line first: the selection of installation tools for undercut anchors must follow the complete-set principle of “dedicated machine with dedicated bit, geometric interlock, torque-controlled fastening”. The core configuration comprises four major components: first, a dedicated undercut alloy drill bit, equipped with a mechanical depth stop ring to ensure the reverse-cone angle and undercut diameter; second, a4-slot (SDS-plus) or 5-slot (SDS-max) rotary hammer/demolition hammer; and third, adedicated go/no-go gauge (hole measuring device); fourth, a properly calibrated torque wrench to achieve precise tightening and expansion of the locking elements. Ordinary drill bits can only drill cylindrical straight holes and cannot form the reverse-cone undercut cavity; if an ordinary drill bit is used anyway, the undercut anchor degenerates into an ordinary friction expansion anchor and loses its mechanical interlock load capacity in cracked concrete and under high-intensity vibration.
Owing to their extremely high ultimate pull-out capacity, low displacement and slip, and fatigue resistance under dynamic loads in cracked concrete, undercut mechanical anchors (Rear Undercut Anchor) are widely used in critical anchoring applications such as primary curtain wall framing, large steel structure connections, nuclear power and rail transit projects. However, no matter how high the quality of the alloy steel, its mechanical performance can only be released through a hole cavity formed to the standard geometry. Starting from the undercut anchoring mechanism, this article systematically compares the essential differences between dedicated undercut drill bits and ordinary drill bits, and provides a selection and quality control guide for complete installation tool sets.
I. Undercut anchoring mechanism and the mechanical logic of drilling
1.1 Mechanical keying effect (Keying Effect)
Traditional expansion anchors rely on sleeve expansion to generate enormous circumferential radial pressure on the wall of a straight hole, resisting tension through interfacial friction. When the concrete cracks under tension (crack widths typically reach 0.3mm~0.5mm) or under strong vibration loads, this approach readily slips and pulls out due to the loss of confining pressure.
Undercut mechanical anchors completely reverse this logic. Installation takes two steps: first a cylindrical hole of the specified depth is drilled into the concrete base material, then a dedicated undercut tool grinds or scrapes a reverse-cone-shaped annular enlarged cavity at the bottom of the hole. When the anchor body is loaded or tightened, the expansion segments at the anchor base open up and fully engage this reverse-cone cavity, forming a mechanical interlock similar to a cast-in hook. Under load, the base material directly bears the concrete compression and shear reactions; there is no long-term sustained expansion stress, and sensitivity to edge failure of the base material (edge distance sensitivity) is greatly reduced.
1.2 The decisive influence of reverse-cone cavity geometric accuracy
The ultimate tensile capacity of an undercut anchor design is calculated on the basis of the concrete failure cone. The reaming inclination angle of the reverse-cone cavity (typically 10°~15°), the undercut depth hef and the reamed bottom diameter dcut all carry micron-level mechanical interlock fitting tolerances. Mismatched reaming geometry leads to the following consequences:
Undercutting too shallow or with insufficient angle: the expansion blades cannot fully open into position, the interlock cross-sectional area is limited, and under strong tension the blades are prone to shear yielding or the anchor slips out entirely.
Reaming depth out of tolerance or bottom diameter too large: the effective anchoring cross-section of the anchor shifts downward, the tightening sleeve cannot sit flush against the base material surface, and the anchor load-bearing system develops initial slack displacement.
II. Core technical differences between dedicated undercut drill bits and ordinary drill bits
Due to schedule or tooling cost constraints, many site workers attempt to form holes with ordinary carbide hammer drill bits — a serious violation that creates engineering safety hazards. The two differ fundamentally and irreconcilably in mechanical construction and working mechanism:
| Comparison dimension | Dedicated undercut drill bit (Dedicated Undercut Bit) | Ordinary carbide drill bit (Standard Drill Bit) |
|---|---|---|
| Geometric cutting mechanism | Equipped with a rotary swinging mechanism or radially extendable alloy cutter wings. The cutting edges are distributed in a reverse-cone profile and can controllably cut the side wall of the hole bottom. | Only the front end is fitted with cross- or flat-type carbide tips; the bit body is a constant-diameter cylindrical spiral flute, and the side edges have no cutting or chip-clearing capability. |
| Depth and stop control | Integrates a rigid mechanical stop ring (limit sleeve). When the limit sleeve sits tightly against the base material surface, the reaming depth is mechanically locked, with tolerance controlled within ±1mm. | No precise stop device; depth is usually judged visually with tape wrapped around the bit or a hand-held ruler, resulting in large hole-depth dispersion and no assurance of the undercut datum level. |
| Reaming action mechanism | Uses a two-step controlled sequence of “drill straight into the hole — axial push — swing/expand cutting”, producing a regular, continuous reverse-cone surface through 360° circumferential cutting. | Capable only of axial linear percussive cutting. If workers manually tilt the hammer drill to “wobble drill”, the hole bottom will assume an irregular egg-shaped oval profile. |
| Cavity load-bearing pattern | The reverse-cone angle precisely matches the anchor expansion segments, forming a full-perimeter face-to-face interlock structure after expansion with no stress concentration. | The expansion segments contact the irregular hole wall only at discrete points and lines, reducing the interlock area by more than 70% and readily causing local crushing and spalling of the concrete hole wall. |
| Compliance with engineering standards | Complies with the JG/T 160 and JGJ 145 standards; installation records accepted by inspection reports can be issued, and physical pull-out acceptance can be passed. | A serious violation.No hole-forming inspection data can be produced; in destructive on-site pull-out tests the anchor readily pulls out directly and is judged non-conforming. |
2.1 The engineering damage caused by manual “wobble drilling”
Some contractors, after reaching the design depth with an ordinary straight-hole drill bit, manually tilt the hammer drill body and swing it in an elliptical circumferential motion — commonly known as “wobble undercutting”. This practice is extremely hazardous:
Bell-mouth enlargement of the hole opening: When an ordinary drill bit swings under force, the lever fulcrum usually falls at the hole opening on the concrete surface. Wobble drilling not only fails to uniformly cut a reverse-cone cavity at the hole bottom, but grinds the outer hole opening into a flared bell shape, so the anchor’s upper shear bearing surface is completely lost and its shear and torsional stiffness drop to zero.
Intensified internal microcracking in the concrete: Under lateral, non-axial percussive impact, ordinary alloy tips generate dense lateral microcracks in the hole wall, significantly reducing the concrete cone failure pull-out capacity of the base material itself.
III. Selection and configuration list for complete undercut anchor installation tool sets
3.1 Selection of power drive equipment (hammer drills/demolition hammers)
Undercut cutting places extremely high demands on the continuous smoothness of mechanical power output. Match the machine power to the anchor nominal size:
M8~M12 small-size undercut anchors: use a heavy-duty hammer drill with a single-blow energy of 2.5J~3.5J and a four-slot (SDS-plus) chuck; it must offer stepless speed adjustment and a combined rotation-stop/pure-rotation function.
M16~M24 large-size undercut anchors: a five-slot (SDS-max) heavy-duty hammer drill must be selected, with a recommended single-blow energy of 7.0J~11.0J, to ensure the undercut cutter wings cut smoothly in hard high-strength concrete (such as C40/C50) and granite aggregate and to prevent the hammer from jamming or the motor from overheating and burning out.
3.2 Complete reaming drill bit sets and guide devices
Two mature technical routes exist in the industry for undercut drilling tools; the selection must strictly match the anchor type:
Dedicated drill bit for pre-undercut systems (the bit performs the undercut): The bit features a rotary outward-swinging cutter head and a rigid limit hood. After drilling the straight hole, switch to this bit, run the hammer drill and push down until the limit hood presses against the base material surface, then gently swing in circles 3~5 turns; the cutter wings extend to complete the reverse-cone undercut. Daring’s DL-H series undercut anchors each come with a dedicated CNC-grade calibrated drill bit that ensures the reverse-cone angle is precisely locked in.
Drive tool for self-undercutting systems (the anchor cuts its own undercut): The anchor body itself carries cutting serrations. After drilling the cylindrical hole with an ordinary straight-hole drill bit, switch to the dedicated percussion drive sleeve or press-in pneumatic impact gun. The anchor sleeve is pressed to the bottom of the hole by mechanical force, and the sleeve’s own cutter teeth scrape the concrete to form the reverse cone; the axial stroke limit of the drive sleeve must be strictly calibrated.
3.3 Depth dedusting and hole cleaning tool set
Undercutting produces more than twice as much fine concrete dust as straight drilling, and a large amount of debris settles and accumulates at the bottom of the reverse-cone cavity. If not cleaned out, the anchor’s expansion segments will be propped up and blocked by the dust and unable to slide into the designed interlock position.
Dedusting tool standard: equip an oil-free industrial high-pressure air pump (working pressure ≥0.6MPa) or a manual two-way air pump; the air hose must be able to reach the hole bottom.
Rigid brush: provide a high-density cylindrical round-wire brush (nylon, steel wire, or copper wire brush) matched to the straight-hole diameter.
Hole cleaning standard: strictly follow the standard “blow twice, brush twice, blow twice” or “blow three times, brush three times, blow three times” procedure until the air blown from the hole bottom is free of dust particles.
3.4 In-process inspection tool: dedicated go/no-go gauge (hole gauge)
Hole forming is concealed work. After undercutting is complete and before the anchor is inserted, a dedicated inspection go/no-go gauge (Go/No-go Gauge) must be used for quality judgment:
Hole depth checking end: verifies that the straight-hole datum depth matches the anchor’s nominal embedment depth. If the depth is insufficient, the anchor must not be installed; if too deep, limiting adjustment washers are required.
Undercut bottom-diameter snap gauge: if the go gauge descends smoothly to the bottom, slides into the reverse-cone cavity and completes its lateral rotational expansion, the reverse-cone cavity geometry has been properly formed; if the gauge cannot expand into position at the bottom, the hole is judged as not undercut or incompletely undercut, and a second drilling pass is required.
3.5 Fastening tool: calibrated torque wrench
The mechanical interlock of an undercut anchor relies on the bolt’s axial force pushing the reverse cone into the expansion segments.It is strictly prohibited to tighten by feel using open-end wrenches or impact electric wrenches.A torque wrench that has passed statutory metrological verification must be used, tightening to the installation torque stated in the product technical briefing Tinst (for example, the regular torque for M12 is controlled at 40~50N·m, and for M16 at 80~100N·m). Tighten until the wrench emits the “click” release signal, and apply an anti-rotation, tamper-evident quality inspection mark at the nut-to-washer interface.
IV. Standardized construction procedure for undercut anchors
To ensure anchoring nodes pass seismic and tensile acceptance, the following six-step standard operating method must be strictly followed on site:
Positioning, layout, and rebar avoidance: use a professional rebar detector to precisely locate the main reinforcement of the concrete member, avoid densely reinforced areas, and ensure the anchor hole axis is perpendicular to the base material surface (the deviation angle should be less than 3°).
Initial drilling of the cylindrical straight hole: use an ordinary straight-hole drill bit matching the anchor’s nominal diameter, fit a fixed-length depth gauge rod on the hammer drill, and drill the initial vertical cylindrical hole; wet drilling with water is strictly prohibited.
Switch to the dedicated drill bit for the second-pass undercut: Fit the matching dedicated undercut alloy drill bit, extend it to the hole bottom until the limit stop housing is fully pressed against the base material surface, perform the steady circular swing per the procedure, and complete the cutting of the reverse-cone cavity at the specified angle.
High-pressure hole flushing and cleaning:Follow the "blow-brush-blow" cycle for at least two rounds to remove all concrete dust and debris accumulated in the reverse-cone cavity and at the hole bottom.
Dedicated hole gauge go/no-go inspection:The quality inspector uses the hole gauge rod to verify hole depth and reverse-cone bottom diameter; only after passing may anchor installation proceed.
Anchor assembly and torque-controlled tightening:Lightly tap the undercut anchor assembly to the hole bottom with a rubber mallet, attach the connecting angle bracket, and use a calibrated torque wrench to applyTinst to reach the mechanically locked state, make marking, and complete concealed-work acceptance.
5. Frequently Asked Technical Questions (FAQ)
Q1 | A crew tried to save effort on site by "circling and wiggling" with an ordinary drill bit and was ordered by the supervisor to stop work for rectification — is there a code basis for this? It is fully supported by the codes.JGJ 145-2013 and the national product standard JG/T 160 both explicitly require that holes for mechanical anchors be formed strictly with the dedicated tools specified in the product certification instructions. Swing reaming with an ordinary drill bit cannot form a standard reverse cone matching the mechanical bearing model; it is not only non-compliant construction, but pull-out sampling tests on the actual work can easily show slip-out failure, and the supervisor has the authority to require removal and scrapping of the affected anchoring points. |
Q2 | How do undercut anchors and self-undercutting anchors differ in tool selection? Both require heavy-impact rotary hammers as the power source, but the drilling tools differ.Undercut anchorsrequire a dedicated drill bit to "ream the cone groove first, then insert the anchor" in concrete, relying on undercut alloy drill bits to form the hole;self-undercutting anchorsinvolve inserting the anchor directly into the pre-drilled straight hole and using a dedicated drive sleeve to strike its slotted sleeve, with the sleeve's own alloy teeth "cutting the bottom while driving". The former adapts better to complex high-strength base materials, while the latter saves one construction step but imposes extremely strict requirements on drive sleeve limit stops. |
Q3 | Installation torqueTinst — the tighter it is turned, the more secure the anchor? This is a common misconception.Too little torque prevents the expansion sleeve segments from being fully pushed into place, resulting in insufficient mechanical interlock; too much torque produces excessive pretension stress in the high-strength bolt itself, which can cause superimposed-stress brittle fracture under later strong wind vibration or seismic action, and can even forcibly crack the local concrete at the hole bottom. A calibrated torque wrench must be used to keep torque strictly within the calibrated parameter range. |
Q4 | How to judge the scrapping criteria when an undercut drill bit wears during use? Wear on the alloy cutting wings on the side of an undercut drill bit reduces the cut bottom diameter. When the matching "go/no-go hole gauge" cannot be smoothly inserted and expanded in a test-cut hole, or a vernier caliper shows the maximum outer diameter of the bit's outward-swinging cutting edges is below the factory limit tolerance, the cutting edges have dulled beyond limits; the bit must be scrapped and replaced immediately and must not be forced into continued use. |
The reliability of engineered structures begins with the smallest details. Undercut mechanical anchors eliminate the instability of traditional friction anchors through bottom mechanical interlocking keys, but this outstanding performance is built entirely on micron-level hole-forming geometric precision. From the selection of the rotary hammer, limit calibration of the undercut alloy drill bit, to high-pressure dust removal and hole cleaning, 100% hole gauge inspection, and torque wrench tightening, only a complete closed-loop tool chain can truly build a subsurface safety barrier against wind loads and strong earthquakes. Shanghai Daring Building Technology Co., Ltd. specializes in providing high-safety-grade integrated post-installed anchoring system solutions; its undercut mechanical anchor series has passed type inspection and seismic dynamic load testing by authoritative national institutions across the entire line, and it supplies strictly calibrated professional undercut drilling tools, hole gauges, and torque installation tool kits, providing physically verified anchoring assurance for major projects.
References
GB 50367-2013 Design Code for Strengthening Concrete Structures — Chapter 16, mandatory provisions on post-installed anchoring connection design and anchor selection
JGJ 145-2013 Technical Specification for Post-Installed Anchoring in Concrete Structures — Chapter 4 design calculations, Chapter 6 installation, and hole-forming inspection acceptance standards
JG/T 160-2017 Mechanical Anchors for Concrete — classification of undercut mechanical anchors, mechanical property requirements, and hole-forming tool compatibility specifications
GB 55002-2021 General Code for Seismic Design of Buildings and Municipal Engineering — general mandatory requirements for seismic protection of non-structural component connections and post-installed anchoring
T/CECS 828-2021 Technical Specification for Seismic Anchoring of Non-Structural Components in Building Engineering — installation workmanship and on-site quality control requirements for mechanical anchors
