First, the conclusion:The Daring aluminium alloy pendant range covers ear-type, C-type (male-and-female), SE combination, H-type and cantilever combination pendants, primarily made of 6063-T6/T5 high-strength aluminium alloy, with an anodized surface and a thickness of approximately 4 mm throughout, providing assured safety. Among the three types of pendant,ear-type pendantsoffer extremely high single-point load capacity and the greatest versatility; they have the largest shipment volume and the best cost-effectiveness, and are suitable for stone and ceramic panels of virtually any thickness;C-type (male-and-female) pendants use a plug-in design with interlocking male and female parts, which can cleverly accommodate panel displacement and stress changes; the cantilever version can be mounted directly on angle steel without angle brackets, and is widely used in high-end projects;SE combination pendants are mainly used to connect external wall panels to structural members and must be used together with cantilever pieces; they can be combined with ear-type, male-and-female and other pendants, and are suitable for projects with high requirements for adjustability and system flexibility. The core logic of selection is:use ear-type for conventional curtain walls, C-type for high-end and large-panel applications, and SE combination for special edge conditions and adjustment requirements。
Scope of application:This article applies to the selection of aluminium alloy pendants in back-bolt dry-hung cladding projects such as stone curtain walls and ceramic panel curtain walls. For pendant selection involving special shapes, oversized panels or super-high-rise buildings, it is recommended to determine the selection in conjunction with a project-specific technical review.
In back-bolt stone curtain-wall projects, the aluminium alloy pendant is the core hub connecting the panel to the sub-frame. It does not rely on adhesive; instead, through precise mechanical engagement, it locks stone weighing several tonnes firmly to the main building. However, many designers and engineers lack a systematic understanding of the structural differences, applicable scenarios and selection logic among C-type, ear-type and SE combination pendants, leading to selection errors. From four perspectives — pendant type analysis, structural comparison, code requirements and Daring selection recommendations — this article provides systematic guidance on pendant selection for stone curtain-wall projects.
I. Core Technical Parameters of Daring Aluminium Alloy Pendants
1.1 Material and Surface Treatment
Daring aluminium alloy pendants are primarily made of 6063-T6 or 6063-T5 high-strength aluminium alloy, formed by hot extrusion, offering high strength, good toughness and high stability. The surface is anodized, producing an oxide film thicker than a naturally formed film; corrosion resistance, wear resistance and appearance are all superior to untreated products, enabling long-term resistance to outdoor environmental erosion.
Pendant thickness is uniformly approximately 4 mm, far exceeding the minimum required by the codes. According to the codes, the thickness of aluminium alloy pendants for stone curtain walls shall be no less than 4.0 mm; Daring pendants use 4 mm as their standard thickness, ensuring safety.
1.2 Daring Pendant Product System
| Pendant type | Structural composition | Connection method | Key features |
|---|---|---|---|
| Ear-type pendant | Aluminium alloy body + three nylon strips (rubber strips) + adjustment screws | Single-piece hanging, clipped directly onto the back bolt | Extremely high single-point load capacity, greatest versatility |
| C-type (male-and-female) pendant | Two aluminium alloy bodies (one male, one female) + adjustment screws | Plug-in design with interlocking male and female parts | Accommodates displacement and stress changes, with uniform overall load distribution |
| SE combination pendant | SE body + matched cantilever piece | Combined installation, compatible with a variety of pendants | Connects external wall panels to structural members, with flexible adjustment |
| H-type pendant | Aluminium alloy body + two nylon strips + two adjustment screws | Two-way adjustment | Suitable for thin ceramic panels or thinner stone |
II. In-Depth Analysis of C-Type, Ear-Type and SE Combination Pendants
2.1 Ear-Type Pendant — The Most Versatile "All-Rounder"
The ear-type pendant consists of an aluminium alloy body, three nylon strips (rubber strips) and adjustment screws, and is divided into flat-ear pendants and recessed-ear pendants. Flat-ear pendants are suitable for use with hammer-in and flush back bolts; for screw-in back bolts, a hexagonal hole can be opened in the flat-ear pendant to perfectly accommodate the protruding hexagonal head of the screw-in back bolt.
The core advantage of the ear-type pendant lies in its extremely high single-point load capacity, high versatility and suitability for stone and ceramic panels of virtually any thickness. It is simple to install, provides better bite force, and is the pendant type with the largest shipment volume and widest use in back-bolt dry-hung cladding work. In conventional stone curtain-wall projects, the ear-type pendant wins on cost-effectiveness and versatility.
2.2 C-Type (Male-and-Female) Pendant — The "Precision Choice" for High-End Projects
The C-type pendant is also called the male-and-female pendant, and consists of two aluminium alloy bodies (one male, one female) and adjustment screws. Its structure uses a flexible plug-in design, allowing fast installation and cleverly accommodating panel displacement and stress changes.
C-type pendants are available in two variants: with cantilever and without cantilever. The cantilevered male-and-female pendant can be installed directly on angle steel without additional angle brackets, reducing the number of connection steps, and is widely used in high-end projects. The overall load distribution of C-type pendants is more uniform, installation is faster than with ear-type pendants, and they are the most expensive of the three common pendant types, making them suitable for large-panel and high-load projects.
Daring male-and-female pendants are mainly used to connect dry-hung panels fitted with hammer-in back bolts to sandwich structural members; they are made of 6063-T6 or 6063-T5 aluminium profile with an anodized surface and good weather resistance.
2.3 SE Combination Pendant — The "Flexible Hub" of System Adjustment
Daring SE pendants are mainly used to connect external wall panels to structural members; they are made of 6063-T6 or 6063-T5 aluminium profile with an anodized surface and good weather resistance. SE combination pendants must be used together with cantilever pieces, which are mostly used to connect edge panels of external walls to structural members.
The core feature of the SE combination pendant is strong system flexibility. By opening holes of different shapes, the SE pendant can be combined with ear-type pendants, male-and-female pendants and other pendant types to suit different connection and adjustment needs. In engineering practice, SE pendant projects should place special emphasis on the factory slotting process for the small flat groove to ensure installation accuracy.
2.4 Multi-Dimensional Comparison of the Three Pendant Types
| Comparison dimension | Ear-type pendant | C-type (male-and-female) pendant | SE combination pendant |
|---|---|---|---|
| Structural composition | Aluminium alloy body + three nylon strips + adjustment screws | Two aluminium alloy bodies (one male, one female) + adjustment screws | SE body + matched cantilever piece |
| Connection method | Single-piece hanging, clipped directly onto the back bolt | Plug-in design with interlocking male and female parts | Combined installation, compatible with a variety of pendants |
| Single-point load capacity | Extremely strong, highly versatile | Strong, with more uniform overall load distribution | Depends on the type of pendant combined with it |
| Accommodation of displacement and stress | Average | Excellent, cleverly accommodates displacement and stress changes | Excellent, with flexible system adjustment |
| Compatible back-bolt type | Flat-ear with hammer-in, recessed-ear with screw-in | Both hammer-in and screw-in | Must be used with cantilever pieces |
| Cantilever function | No cantilever; must be used with angle brackets | Cantilever version can be mounted directly on angle steel | None |
| Installation speed | Fast | Faster; the plug-in design improves construction speed | Moderate; requires combined installation |
| Suitable projects | Conventional stone curtain walls, projects with high versatility requirements | High-end projects, large panels, high-load projects | Projects requiring flexible adjustment and edge coordination |
III. Core Code Requirements for Aluminium Alloy Pendants
3.1 Thickness Requirements
According to the codes, for stone curtain walls the thickness of aluminium alloy pendants shall be no less than 4.0 mm, and the thickness of stainless steel pendants shall be no less than 3.0 mm. For porcelain panel curtain walls, the cross-sectional thickness of aluminium alloy profiles for short pendants should be no less than 2.0 mm, and for continuous pendants no less than 1.5 mm. Daring aluminium alloy pendants are all approximately 4 mm thick, satisfying and exceeding the code requirements.
3.2 Material Requirements
According to the codes, when hot-extruded aluminium alloy pendants are used, the material shall be 6061 T5 (T6), 6063 T5 (T6) or 6063A T5 (T6). Daring aluminium alloy pendants are primarily made of 6063-T6/T5, in compliance with the code requirements. The pendant surface shall undergo anodizing treatment to improve durability.
3.3 Connection Requirements
Each pendant should have no fewer than two fixing bolts to ensure connection reliability. Daring supplies 304/316 stainless steel bolts that meet the requirements of curtain-wall projects for seismic resistance, fatigue resistance and long-term durability.
IV. Daring Pendant Selection Recommendations
4.1 Selection by Project Type
| Project type | Recommended pendant type | Core reason |
|---|---|---|
| Conventional stone curtain wall | Ear-type pendant | Highest versatility, best cost-effectiveness, largest shipment volume |
| High-end project / large panel | C-type (male-and-female) pendant | Higher overall strength, uniform load distribution, cantilever version reduces angle brackets |
| Edge coordination / flexible adjustment | SE combination pendant + cantilever piece | Strong system flexibility, compatible with a variety of pendants |
| Thin ceramic panel | H-type pendant | Two-way adjustment, suitable for installation of thin panels |
| Seismic-design zone | C-type (male-and-female) pendant | Plug-in design accommodates displacement and stress changes, with better seismic performance |
4.2 System Compatibility Principles
Daring provides an integrated solution of anchors and pendants, avoiding the compatibility risks of mixing components from different brands. Its H-type, ear-type and C-type pendants can be precisely matched with self-developed screw-in and hammer-in back bolts, ensuring that dimensional tolerances and mechanical properties between pendant and back bolt are matched.
The Daring back-bolt dry-hung cladding system has passed Tongji University's grade-9 rare-earthquake seismic test and authoritative testing by the National Building Materials Testing Center, with acceleration reaching 1.24g; as an important part of the system, the pendant's performance has been verified as part of the whole system.
4.3 Construction Compatibility Requirements
Back-bolt and pendant matching: hammer-in back bolts are paired with flat-ear pendants; screw-in back bolts are paired with recessed-ear pendants or flat-ear pendants with hexagonal holes.
Use of cantilever version: when using a cantilevered C-type pendant, it can be installed directly on angle steel without additional angle brackets, simplifying the node detail.
SE pendant slotting: SE pendant projects should place special emphasis on the factory slotting process for the small flat groove to ensure installation accuracy.
Prohibited pendant types: angled insert-type pendants and T-type pendants shall not be used in dry-hung stone curtain walls.
V. Frequently Asked Questions
| Q1 | Which is better, the ear-type pendant or the C-type pendant? Neither is absolutely better; it depends on the application. The ear-type pendant offers the highest versatility and best cost-effectiveness and is suitable for conventional stone curtain walls; the C-type pendant has higher overall strength and more uniform load distribution, accommodates displacement and stress changes, and is suitable for high-end projects and large panels. Choose ear-type for conventional curtain walls and C-type for high-end projects. |
| Q2 | What is the difference between an SE combination pendant and a C-type pendant? The SE combination pendant is mainly used to connect external wall panels to structural members and must be used together with cantilever pieces; it offers strong system flexibility and can be combined with ear-type, male-and-female and other pendants. The C-type (male-and-female) pendant uses a plug-in design with interlocking male and female parts for fast installation and uniform overall load distribution. SE combinations suit edge coordination and flexible adjustment needs, while C-type suits high-end large-panel projects. |
| Q3 | What material and thickness are Daring aluminium alloy pendants made of? Daring aluminium alloy pendants are primarily made of 6063-T6/T5 high-strength aluminium alloy, approximately 4 mm thick, with an anodized surface. 6063-T6 is stronger than T5 and is suitable for projects with higher load requirements. The codes require aluminium alloy pendant thickness of no less than 4.0 mm, which Daring pendants satisfy and exceed. |
| Q4 | What is the difference between a C-type pendant with and without a cantilever? A cantilevered male-and-female pendant can be installed directly on angle steel without additional angle brackets, reducing connection steps and simplifying the node detail; it is widely used in high-end projects. A C-type pendant without a cantilever must be used together with angle brackets. The choice can be determined according to the project's node design and cost requirements. |
| Q5 | Can Daring pendants be used with back bolts of any brand? Mixing is not recommended. Daring provides an integrated solution of anchors and pendants; its pendants are precisely matched with self-developed screw-in and hammer-in back bolts, with verified dimensional tolerances and mechanical properties. Dimensional tolerances and connection methods may differ between components from different brands, and mixing may introduce compatibility risks. |
| Q6 | What project applications have Daring pendants been used in? Daring back-bolt and pendant systems have been used in many high-end projects, including the Guangzhou International Finance Center (main tower 440.75 m high), Shanghai Tower, the curtain-wall renovation project of the Ministry of Foreign Affairs of China, the First Historical Archives of China (Luban Award), and the headquarters of the Asian Infrastructure Investment Bank. |
The Daring aluminium alloy pendant range covers ear-type, male-and-female, H-type, SE combination and cantilever combination pendants, as well as angle brackets and corner connectors, primarily made of 6063-T6/T5 high-strength aluminium alloy with an anodized surface. It is designed specifically for back-bolt dry-hung cladding systems and is suitable for connecting, fixing and corner-joining various external wall panels and structural members. Daring provides an integrated solution of anchors and pendants, avoiding the compatibility risks of mixing brands; the back-bolt dry-hung cladding system has passed Tongji University's grade-9 rare-earthquake seismic test with acceleration reaching 1.24g. For guidance on pendant selection calculations and node design for specific projects, please consult the Daring technical team.
References
JGJ 133-2001, Technical Code for the Engineering of Metal and Stone Curtain Walls — material and thickness requirements for pendants
JGJ 336-2016, Technical Code for the Engineering of Man-Made Panel Curtain Walls — pendant requirements for back-bolt support connections
GB/T 5237.1-2017, Aluminium Alloy Building Profiles — Part 1: Base Material — technical requirements for aluminium alloy profiles
Daring website — SE combination pendant product parameters
Daring website — How much do back-bolt pendants cost? Which is better, C-type or ear-type
Daring website — Understanding curtain-wall back-bolt pendants in one article
