Product Knowledge

What to Do When Undercut Anchor Drilling Depth Is Insufficient? Daring On-Site Remedies | Tiered Handling Plan and Re-Drilling Process

Views: 0Posted on: 2026-10-08

The bottom line first:The most direct consequence of insufficient drilling depth for an undercut anchor isthat the undercut cavity at the hole bottom cannot fully form and the mechanical interlock structure fails, with load capacity potentially reduced by more than 50%; in pull-out tests the anchor is pulled out whole rather than the threaded rod breaking. Once insufficient hole depth is discovered, the correct remedy isto abandon the original hole and re-drill at a new location: tightly seal the original hole with high-strength epoxy mortar, re-drill at a position ≥2 times the hole diameter from the original hole, strictly follow the four-step procedure of drilling → reaming → hole cleaning → installation, and repeat pull-out testing for verification. It should be noted in particular that the undercut anchor relies onmechanical interlock rather than adhesive bonding, so incorrect methods such as "injecting adhesive as a remedy" or "forcing installation with increased torque" are strictly prohibited. The threaded rod of the Daring undercut anchor is provided withan embedment depth line marking; during installation, hammering until the embedment depth line is flush with the substrate surface indicates the anchor is fully seated. Supplied with original undercut drill bits and hammering sleeves, drilling accuracy is assured at the source.

The load capacity of an undercut anchor depends on the mechanical interlock between the undercut cavity at the hole bottom and the anchor's key segments. If the drilling depth is insufficient, the undercut cavity cannot fully form, the interlock structure cannot be established, and anchoring capacity is out of the question. Yet on construction sites, insufficient drilling depth is one of the most frequent quality problems. This article systematically analyzes the causes, consequences, and Daring's on-site remedies for insufficient drilling depth of undercut anchors from four dimensions: code requirements, failure mechanisms, on-site treatment solutions, and prevention at the source.

I. Code requirements for the drilling depth of undercut anchors

1.1 Relationship between effective embedment depth and drilling depth

According to JGJ 145-2013 "Technical Specification for Post-installed Anchors in Concrete Structures", the effective embedment depth hef is the depth of the point of maximum compression between the anchor's expansion cone and the hole wall. For undercut anchors, hef is a product-specific parameter determined by the anchor's structural design; the drilling depth includes the straight-hole section and the reamed section, so the drilling depth is usually greater than the effective embedment depth.

Taking the Daring undercut anchor as an example, the M12/18×80 size has a drilling diameter of 18mm and an effective embedment depth hef of 80mm, with a corresponding drilling depth of 90mm; the M16/22×100 size has a drilling diameter of 22mm and an effective embedment depth of 100mm, with a drilling depth of 110mm. During construction, holes must be drilled strictly to the drilling depth specified in the product specification table, and the drilling depth deviation should be kept within +5mm.

1.2 Code detailing requirements for embedment depth

Clause 7.1.4 of JGJ 145-2013 stipulates that for anchors used in load-bearing structures, the embedment depth hef shall not be less than 60mm. Clause 16.4.2 of GB 50367-2013 likewise stipulates that the embedment depth hef determined by detailing requirements shall not be less than 60mm and shall not be less than the concrete cover thickness. In seismic design zones, the embedment depth requirements are further increased on this basis.

In addition, Clause 7.1.1 of JGJ 145-2013 stipulates that for undercut-type anchors, the thickness h of the base concrete shall not be less than 2hef, and h shall be greater than 100mm. This means the drilling depth of the anchor is constrained not only by the anchor's own size but also by the thickness of the base concrete slab.

II. Failure mechanisms of insufficient drilling depth

2.1 Mechanical interlock cannot fully form

The anchoring principle of the undercut anchor is a secondary reaming at the hole bottom: the reamed reverse-cone cavity and the anchor's expanded key segments form an interlocking mechanism that carries load through mechanical interlock. Insufficient drilling depth means there is not enough space in the undercut section at the hole bottom, so the undercut cavity cannot fully form. The key segments can only contact the concrete locally at single points, the effective bearing area shrinks dramatically, and the anchor is pulled out whole during pull-out with no safety margin whatsoever.

To put it figuratively: an undercut anchor works by "locking in"—load is transferred through the geometric interlocking of the reverse-cone cavity at the hole bottom and the key segments. Insufficient hole depth is like a keyhole cut too shallow: the key cannot be inserted fully, the lock cylinder cannot turn, and the interlocking action fails completely.

2.2 Quantitative analysis of load capacity loss

The load capacity loss of an undercut anchor is directly related to the degree of insufficient undercutting. According to industry measured data (intact C30 concrete under standard embedment conditions):

Degree of insufficient undercuttingLoad capacity lossFailure behavior
Slight deficiency (deviation ≤10%)25%~40%Barely meets short-term static load requirements; degradation amplifies to 50% under seismic and dynamic load conditions
Moderate deficiency (deviation 20%–30%)50%~60%Key segments expand only halfway; batch failure in third-party witnessed pull-out tests
Severe deficiency (almost no effective reverse cone)60%~80%Equivalent to an ordinary friction-type expansion anchor; complete failure under seismic and dynamic loads

Taking the M12 undercut anchor as an example, the standard undercut diameter is 24mm; if the actual reaming reaches only 20mm, load capacity drops directly by 60% and third-party witnessed pull-out tests fail in batches.

2.3 Chain-reaction failures caused by insufficient hole depth

  • Direct failure of pull-out testing: JGJ 145-2013 requires the measured ultimate tensile force to be ≥1.5 times the design value. With the undercut missing, the ultimate load shrinks dramatically, third-party testing directly condemns the anchors, and the entire batch must be reworked.

  • Complete failure under seismic and dynamic loads: The core advantage of the undercut anchor is stability under 2 million cycles of alternating load. Without proper undercutting, only local friction remains; under the long-term vibration of fans, elevated curtain walls, and equipment foundations, continuous slippage occurs with a risk of falling.

  • Amplified hazards in cracked concrete: Standard undercutting can accommodate micro-cracks of 0.3mm; with insufficient undercutting, local stress becomes highly concentrated, cracks rapidly tear through the concrete at the hole bottom, and the anchor pulls out whole.

III. Daring's on-site remedies: tiered treatment plan

3.1 Core principles

Insufficient drilling depth of an undercut anchor isan irreversible construction defect. All remedial measures must be confirmed and signed off by the supervising engineer and the design institute before implementation. The choice of remedy depends on three key factors: the degree of hole depth deviation, the anchor type, and the load class.

Special reminder: The undercut anchor relies on mechanical interlock rather than adhesive bonding, so the practice of "injecting adhesive into the original hole and then installing the anchor" is strictly prohibited. Adhesive injection cannot form an effective mechanical interlock, the anchor's load-bearing mode is completely altered, and load capacity cannot be guaranteed. This is entirely different from the remedial logic of "re-injecting adhesive and re-installing" for chemical anchors.

3.2 Comparison table of tiered remedies

Degree of hole depth deviationTreatment planKey operating pointsScope of application
Deviation ≤10%Retention after assessment + reinforcementAfter design verification confirms the load capacity meets requirements, additional anchors of the same size can be installed at compliant adjacent positions to share the loadNon-critical load-bearing locations and multi-hole curtain wall structures
Deviation 10%–30%Abandon the original hole and re-drill at a new locationTightly seal the original hole with high-strength epoxy mortar; after adequate curing, re-drill at a position ≥2 times the hole diameter from the original holeAll load-bearing structure anchoring
Deviation >30%Full-batch inspection and reworkRemove all non-conforming anchors, re-set out and re-drill after sealing the original holes, and conduct comprehensive pull-out testingAll conditions; must be strictly enforced

3.3 Standard operating procedure for re-drilling at a new location

Re-drilling at a new location is the core remedy for insufficient hole depth of undercut anchors. The specific steps are as follows:

  • Abandon the original hole: tightly seal the original hole with high-strength epoxy repair mortar or non-shrink epoxy mortar and cure until the strength reaches specification.

  • Relocation and setting out: re-set out at a position ≥2 times the hole diameter from the original hole, avoiding the influence zone of the original hole and any rebar.

  • Re-drilling: drill with a matched straight-hole drill bit to the specified depth; the drilling depth should equal the embedment depth plus the height of the reamed section, with deviation kept within +5mm.

  • Reaming: use the Daring original specialized undercut drill bit to ream the hole bottom a second time, forming a well-shaped reverse-cone cavity. The undercut diameter and depth allow only positive deviation (larger, not smaller); negative deviation is not permitted.

  • Hole cleaning: after reaming, use an air blower aimed at the hole to blow out dust until no dust escapes from the hole.

  • Anchor installation: use the specialized hammering sleeve to drive the anchor into position, hammering until the embedment depth line on the threaded rod is flush with the substrate surface, confirming the anchor is fully installed.

  • Pull-out testing: after installation, repeat pull-out testing to verify that the load capacity meets the design requirements.

3.4 Incorrect "remedies" that are strictly prohibited

  • It is strictly prohibited to inject adhesive into the original hole and then install an undercut anchor: The working principle of the undercut anchor is completely different from that of the chemical anchor; it relies on mechanical interlock rather than adhesive bonding. Adhesive injection cannot form an effective reverse-cone interlock, and anchoring capacity cannot be guaranteed.

  • It is strictly prohibited to force installation with excessive installation torque: Excessive torque causes the anchor to over-rotate in the hole, damaging the threads, reducing the effective load-bearing area, and even breaking the threaded rod.

  • It is strictly prohibited to install an undercut anchor in a straight hole without reaming: An undercut anchor in an un-reamed hole performs even worse than an ordinary sleeve expansion anchor and is pulled out directly in pull-out tests.

  • It is strictly prohibited to stuff wood chips, wire, or gravel into the gap: These loosen under vibration and load and fail within a short time.

  • It is strictly prohibited to fill with ordinary cement mortar: It shrinks heavily, is highly brittle, and has extremely poor pull-out resistance.

IV. Prevention at the source: Daring's drilling accuracy assurance plan

4.1 Use the original undercut drill bit

Daring undercut anchors are supplied with original undercut drill bits and powered installation tools. Using an unmatched undercut drill bit leads to dimensional deviation of the undercut cavity and an irregular cavity shape, with eccentric loading on the key segments. Daring original undercut drill bits are precision machined to ensure the dimensional accuracy and surface quality of the undercut cavity.

4.2 Using the embedment depth line marking on the threaded rod to control installation accuracy

The threaded rod of the Daring undercut anchor is provided withan embedment depth line marking. During installation, the specialized hammering sleeve drives the anchor into position; when the embedment depth line is flush with the substrate surface, the anchor has reached the specified depth. This marking is a direct means of controlling installation accuracy on site, with no additional measuring tools required.

4.3 Hole-by-hole inspection of drilling depth

Clause 9.3.3 of JGJ 145-2013 explicitly requires that "anchor hole depth shall be measured". During construction, use a depth gauge or a hole-measuring rod to inspect the drilling depth hole by hole, ensuring compliance with the product manual. In high seismic intensity zones or for important projects, hole-by-hole inspection is required, and non-conforming holes should be abandoned and re-drilled.

4.4 Rebar detection before construction

A common cause of insufficient drilling depth is encountering rebar or embedded conduits during drilling, which makes operators hesitant to drill deeper. Before formal drilling, scan the drilling area with a rebar detector and confirm there are no rebar or conduit obstructions before drilling. In areas with dense rebar, coordinate with the designer to adjust hole positions.

V. Technical parameter reference for the Daring undercut anchor

SizeDrilling diameterReaming diameterDrilling depthMaximum installation torque
M88mm10.5mm30mm10N·m
M1010mm13.5mm40mm20N·m
M1212mm16mm40mm40N·m
M1616mm21mm50mm80N·m
M2020mm26mm60mm150N·m

The Daring undercut anchor is also available in deeper sizes such as M12/18×80 (drilling depth 90mm), M12/18×100 (drilling depth 110mm), M16/22×100 (drilling depth 110mm), M16/22×120 (drilling depth 130mm), and M20/28×160 (drilling depth 180mm), selectable according to project requirements.

VI. Frequently asked questions

Q1What are the consequences of insufficient drilling depth for an undercut anchor?
The undercut cavity at the hole bottom cannot fully form and the mechanical interlock structure fails. Load capacity loss depends on the degree of deviation: a slight deficiency causes a 25%–40% loss, a moderate deficiency a 50%–60% loss, and a severe deficiency a 60%–80% loss. In pull-out tests the anchor is pulled out whole rather than the threaded rod breaking—a brittle failure with no warning.
Q2Can insufficient drilling depth of an undercut anchor be remedied by injecting adhesive?
No. The undercut anchor relies on mechanical interlock rather than adhesive bonding; adhesive injection cannot form an effective reverse-cone interlock, the anchor's load-bearing mode is completely altered, and anchoring capacity cannot be guaranteed. This is entirely different from the remedial logic of "re-injecting adhesive and re-installing" for chemical anchors. The only compliant solution is to abandon the original hole and re-drill at a new location.
Q3How far from the original hole should the new hole be when re-drilling?
The new hole should be drilled at a position ≥2 times the hole diameter from the original hole, avoiding the influence zone of the original hole and any rebar. For example, the M12 undercut anchor has a drilling diameter of 12mm, so the relocation distance should be ≥24mm. After relocation, pull-out testing must be repeated to verify the load capacity.
Q4How does the Daring undercut anchor control drilling depth accuracy?
The threaded rod of the Daring undercut anchor has an embedment depth line marking; during installation, the specialized hammering sleeve drives the anchor into position, and hammering until the embedment depth line is flush with the substrate surface indicates full installation. The supplied original undercut drill bit ensures the dimensional accuracy and surface quality of the undercut cavity. The drilling depth deviation should be kept within +5mm.
Q5What if rebar is hit during drilling, resulting in insufficient depth?
Before construction, scan the drilling area with a rebar detector. If rebar is encountered during drilling, coordinate with the designer to adjust the hole position. If the hole position cannot be adjusted, a deeper hole position may be used to avoid the rebar, or the scheme may be switched to chemical anchors. All remedial measures must be confirmed by the supervising engineer and the designer before implementation.
Q6What deeper sizes does the Daring undercut anchor offer?
The Daring undercut anchor is available in a variety of deeper sizes, including M12/18×80 (drilling depth 90mm), M12/18×100 (drilling depth 110mm), M16/22×100 (drilling depth 110mm), M16/22×120 (drilling depth 130mm), and M20/28×160 (drilling depth 180mm), selectable according to project load requirements and substrate conditions.

The Daring undercut anchor has passed more than ten authoritative tests including EU ETA certification, Class S anchor certification, mechanical property testing, the 2-million-cycle fatigue test, the 120-minute fire resistance test, high-temperature testing, seismic testing, coating thickness inspection, salt spray testing, and elongation and thread accuracy testing, with materials covering Class 5.8/8.8 carbon steel and 304/316 stainless steel and sizes covering M8-M20. Daring supplies matching original undercut drill bits, hammering sleeves, and powered installation tools, ensuring drilling and reaming accuracy is precisely controlled. For undercut anchor drilling depth calculations and on-site technical guidance for specific projects, please contact the Daring technical team.

References

JGJ 145-2013 Technical Specification for Post-installed Anchors in Concrete Structures—Anchor drilling depth, effective embedment depth, and construction and acceptance requirements

GB 50367-2013 Design Code for Strengthening Concrete Structures—Detailing requirements for embedment depth

JG/T 160-2017 Mechanical Anchors for Use in Concrete—Classification and technical requirements for mechanical anchors

Daring website—A complete guide to undercut mechanical anchor specifications and installation methods

Daring website—How to determine the effective embedment depth of undercut mechanical anchors? Understanding the code requirements in one article

Daring website—The 5 most common undercut anchor installation mistakes: no reaming, no hole cleaning, wrong torque

Daring website—What to do about concrete edge spalling during mechanical anchor reaming? Post-installed rebar solutions for insufficient edge distance

Sohu—Undercut mechanical anchors: how much load capacity is lost when the undercut drilling falls short?

Shanghai Huiyu—Anchor drilled too shallow: demolish and redo? Don't rush—first look at these "remedy" options

Daring website—Mechanical anchor product range

Back to Daring Home  Back to Top