Product Knowledge

What to do when concrete spalls while reaming for mechanical anchors? Post-installed rebar solutions for short edge distances

Views: 0Posted on: 2026-09-02

The conclusion first:Concrete edge chipping during mechanical anchor undercutting isinsufficient edge distancethe most common construction quality problem it causes. According to JGJ 145-2013 Technical Specification for Post-Installed Anchoring of Concrete Structures, the minimum edge distance for undercut anchors should be no less than5 times the anchor diameter (5d), and the minimum spacing should be no less than6 times the anchor diameter (6d). When the anchor is too close to the component edge, the squeezing force generated by undercutting concentrates in the shallow surface layer at the hole mouth, causing the concrete tosplit, spall and chip. Once chipping occurs, the hole is invalid and remedial measures must be taken: for minorlocal chipping, high-strength repair mortar can be used for repair and the hole relocated and re-drilled; for severeoverall failure, it is necessary toinstall additional post-installed reinforcement- install a reinforcement mesh in the chipped area, restore the concrete section with high-strength grout or epoxy mortar, then re-drill and undercut after curing reaches the required standard. Daring undercut anchors usedeep mechanical keying at the bottom of the holedesign, with no shallow expansion stress, effectively reducing the risk of edge chipping.

In post-installed anchoring work, concrete edge chipping during mechanical anchor undercutting is a verycommon and troublesomeproblem on construction sites. Locations such as beam and column edges, cantilever slab ends and curtain wall closures often cannot meet the minimum edge distance required by the standards because component dimensions are limited. Once chipping occurs, it not only affects the construction schedule but may also leave serious safety hazards. This article systematically analyzes the response strategies for chipping and insufficient edge distance during mechanical anchor undercutting from the perspectives of causes, standard requirements, preventive measures and post-chipping treatment options.

I. Root causes of concrete edge chipping

1.1 Insufficient edge distance - the primary cause of chipping

The most fundamental cause of concrete edge chipping during mechanical anchor undercutting isthe anchor being too close to the component edge. Under load, the anchor forms a concrete tensile failure cone within the base material to carry the load, so the standards require sufficient edge distance to be maintained. When the anchor is placed close to the component edge,the external confinement is weak, and the squeezing force generated by undercutting concentrates in the shallow surface layer at the hole mouth, easily causing the concrete tosplit, spall and chip。

According to Clause 7.1.2 of JGJ 145-2013, the minimum spacing s and minimum edge distance c of anchor groups should be determined on the basis of the anchor product'scertification report. For undercut anchors, in the absence of a certification report, the minimum edge distance should be no less than5 times the anchor diameter (5d), and the minimum spacing should be no less than6 times the anchor diameter (6d). Taking an M12 undercut anchor as an example, the minimum edge distance should be no less than60mm. The minimum edge distance should also be no less than2 times the maximum aggregate particle size。

It should be noted in particular thatinsufficient edge distance not only causes chipping during installation but also leads to a serious reduction in load capacity. When the edge distance is insufficient, the concrete tensile failure cone is incomplete and the load capacity drops significantly. If the spacing is also insufficient, the reduction is further amplified.

1.2 Other causes of chipping

In addition to insufficient edge distance, the following factors can also cause concrete chipping during undercutting:

  • Excessive installation torque: the expansion segments of the undercut anchor are over-expanded, causing local crushing and spalling of the concrete and direct chipping when the edge distance is small

  • Insufficient base material strength or loose concrete: in renovation projects on old buildings, severe concrete carbonation or low strength means the hole wall cannot withstand the undercutting pressure

  • Substandard undercutting quality: the reverse-cone cavity at the bottom of the hole is not properly formed, or the undercutting bit is used incorrectly, causing the hole wall concrete to be crushed directly

  • Hitting coarse aggregate or rebar during drilling: the drill bit deviates when it encounters a hard object, resulting in an enlarged hole diameter and a cracked hole wall

II. Prevention strategies for insufficient edge distance

2.1 Verify edge distance requirements before construction

Every anchor product hasminimum edge distance and minimum spacing requirements, which must be confirmed against the product technical data sheet before construction and cannot be estimated from experience. The construction drawings should clearly indicate the edge distance and spacing requirements, and site setting-out should be carried out strictly in accordance with the drawings.

2.2 Prefer anchors without shallow expansion stress

Edge distance requirements vary significantly between anchor types. Conventional expansion anchors rely entirely on radial expansion against the hole wall to carry load, andthe squeezing force is greatest at the hole mouth, so with insufficient edge distance, tightening the nut or applying tension causes chipping. Conventional chemical anchors and reverse-cone chemical anchors mainly rely on adhesive bonding to the hole wall, with the load-bearing zone concentrated in the middle and upper part of the anchor hole; when the edge distance is insufficient, the concrete cover thickness at the edge is inadequate and edge tearing is likely.

Undercut mechanical anchorsare currently the only mechanically locking anchors suitable for small edge distances and narrow-edge components. Through secondary undercutting, they form a reverse-cone cavity at the bottom of the drilled hole; once the expansion segments at the anchor base expand, they forma rigid mechanical key with the deep concrete, so all loads are concentrated and transferred to the dense deep concrete at the bottom of the hole, therebyavoiding the weak zone at the component edge. Conventional undercut anchors can be used normally at a minimum edge distance of≥3d. Daring undercut anchors usedeep mechanical keying at the bottom of the holedesign, with no shallow expansion stress, effectively reducing the risk of edge chipping.

2.3 Control installation torque

Excessive installation torque is ahuman factorin causing chipping. Acalibrated torque wrenchmust be used; pneumatic or impact wrenches must never be used to tighten directly to failure. Standard JG/T 160-2017 requires the ultimate torque to be at least 1.3 times the installation torque, and exceeding this range involves risk. During construction, tighten in two stages: first hand-tighten until snug (about 1/2 of the rated torque), then tighten evenly to the specified torque.

III. Remedial measures after chipping

3.1 Minor chipping - repair and relocate the hole

If the chipping is limited (chipping depth less than 10mm, not affecting the effective embedment depth), the following steps can be taken:

  • Clean the original holethoroughly, removing loose concrete fragments

  • Usehigh-strength epoxy repair mortaror polymer cement mortar to seal the original hole and the chipped areacompactly, and cure until the design strength is reached

  • At a locationat least 2 hole diametersaway from the original holere-drill and re-undercut, ensuring that the new hole meets the minimum edge distance requirement

  • and conduct a new pull-out test to verify the load capacity

3.2 Severe chipping - restore the section with post-installed reinforcement

When the chipping is extensive (chipping depth of 15mm or more, or the chipping has affected the effective embedment depth), or the component edge already showsoverall cracking, corner spalling or loose damage, it is necessary to adopt apost-installed reinforcementscheme to restore the concrete section:

  • Step 1: Surface preparation- chisel away the concrete in the chipped area down to a sound base, removing loose particles and dust

  • Step 2: Install post-installed rebar- in the chipped area, as required by the design,install a reinforcement mesh. The distance between the post-installed rebar and the concrete edge should not be less than5d, and should not be less than100mm. Where there are transverse bars perpendicular to the direction of the post-installed rebar between the rebar and the concrete edge, and there are at least 2 transverse bars within the embedment depth range, the minimum distance between the rebar and the edge may be appropriately reduced, but should not be less than50mm. The post-installed rebar should usea specialized anchoring adhesive, and the embedment depth should meet the requirements of GB 50367-2013

  • Step 3: Restore by pouring- usehigh-strength groutorepoxy mortarto restore the concrete section by pouring, and compact it by vibration

  • Step 4: Curing- cure according to the material requirements until the design strength is reached

  • Step 5: Re-drill and re-undercut- after curing reaches the required standard, re-drill and re-undercut in the newly restored section and install the anchor

The core logic of the post-installed reinforcement solutionis thatthe damaged concrete section is restored with post-installed rebar and grout, so that the component edge regains sufficientconcrete cover thickness, thereby satisfying the anchor's edge distance requirements. Post-installed rebar technology is a relatively simple and effective connection and anchoring method in the strengthening and renovation of concrete structures, and can be used to remedy situations where rebar was omitted or deviates from its design position.

3.3 Cases beyond repair - void the hole and re-drill

The following situationscannot be remedied, so the hole must be voided and re-drilled or the scheme adjusted:

  • Thin plaster and surface delamination- the base material itself has quality problems

  • Old, loose concrete with severe carbonation- the deep base material no longer provides adequate anchoring conditions

  • A hole located immediately beside a cut edge of the component- insufficient effective concrete thickness, making it impossible to form a load-bearing locking layer at the bottom

  • Key load-bearing nodes subject to high seismic demand, high fatigue or frequent dynamic loads- the use of extremely small edge distances is strictly prohibited

IV. Regulatory basis

The treatment of chipping and insufficient edge distance during mechanical anchor undercutting should meet the following standard requirements:

  • JGJ 145-2013Technical Specification for Post-Installed Anchoring of Concrete Structures - Clause 7.1.2 specifies the requirements for the minimum spacing s and minimum edge distance c of anchor groups

  • GB 50367-2013Design Code for Strengthening Concrete Structures - structural requirements for post-installed rebar embedment depth, spacing and edge distance

  • JG/T 160-2017Mechanical Anchors for Concrete - product performance and inspection standards

V. Frequently asked questions

Q1What causes concrete chipping during mechanical anchor undercutting?
The main cause is insufficient edge distance - the anchor is too close to the component edge. The squeezing force from undercutting concentrates in the shallow surface layer at the hole mouth, and the external confinement is weak, causing the concrete to split, spall and chip. Excessive installation torque, insufficient base material strength and substandard undercutting quality can also cause chipping.
Q2What is the minimum edge distance requirement for mechanical anchors?
According to JGJ 145-2013, the minimum edge distance for undercut anchors should be no less than 5 times the anchor diameter (5d), and the minimum spacing no less than 6 times the anchor diameter (6d). Taking an M12 anchor as an example, the minimum edge distance should be no less than 60mm. The specific values should be based on the anchor product's certification report.
Q3How should chipping after undercutting be handled?
For minor chipping (depth less than 10mm): seal the original hole with high-strength epoxy repair mortar and re-drill at a relocated position. For severe chipping (depth of 15mm or more, or affecting the embedment depth): post-installed reinforcement is required - install a reinforcement mesh, restore the concrete section with high-strength grout, then re-drill and re-undercut after curing reaches the required standard. Cases beyond repair should be voided and re-drilled.
Q4Can undercut anchors solve the problem of insufficient edge distance?
Yes. Undercut anchors are currently the only mechanically locking anchors suitable for small edge distances and narrow-edge components, and they can be used normally at a minimum edge distance of 3d or more. They carry load through deep mechanical keying at the hole bottom, with no shallow expansion stress, effectively reducing the risk of chipping.
Q5Can Daring undercut anchors avoid chipping?
Daring undercut anchors use deep mechanical keying at the bottom of the hole; all loads are concentrated and transferred to the dense deep concrete at the hole bottom, with no shallow expansion stress, effectively reducing the risk of chipping. However, where the edge distance is severely insufficient (less than 3d) or the base material itself has quality problems, careful evaluation is still required.

Daring undercut anchors usedeep mechanical keying at the bottom of the holedesign; through secondary undercutting, a reverse-cone cavity is formed at the bottom of the drilled hole, and once the expansion segments at the anchor base expand, they form a rigid mechanical key with the deep concrete, so all loads are concentrated and transferred to the dense deep concrete at the hole bottom,with no shallow expansion stress, effectively reducing the risk of chipping. The products have passed numerous authoritative certifications including S-grade anchor certification, 2-million-cycle fatigue testing, 120-minute fire resistance testing and seismic testing, and are supplied with original-manufacturer undercutting drill bits and electric installation tools. For advice on preventing and treating chipping of undercut anchors in specific projects, please consult the Daring technical team.

References

Daring website - Undercut mechanical anchor product page

Daring website - Undercutting: the key to undercut anchor installation

Daring website - How to use undercut mechanical anchors

JGJ 145-2013 Technical Specification for Post-Installed Anchoring of Concrete Structures

GB 50367-2013 Design Code for Strengthening Concrete Structures

JG/T 160-2017 Mechanical Anchors for Concrete

Back to Daring Home  Back to Top