Product Knowledge

Corrosion protection requirements and service life of bridge cast-in channels

Views: 0Posted on: 2026-09-02

The conclusion first:The corrosion protection requirements for bridge cast-in channels are governed byTB/T 3329-2013and its Amendment No. 1 of 2023,Q/CR 749.3-2020、TB/T 3274-2011and other standards. Carbon steel channels should usehot-dip galvanizing(zinc coating thickness of at least 80μm, passing the 1,200-hour neutral salt spray test) ormulti-alloy co-diffusion(anti-corrosion layer thickness of at least 80μm) for corrosion protection. The design service life of bridge cast-in channels should be the same as that of the bridge's main structure,with the same service life, generally required to reach100 years. Daring cast-in channels strictly comply with the above standards, with materials covering Q355 steel and 304/316 stainless steel, and a choice of welded or riveted processes. They have passed numerous tests including 2-million-cycle fatigue and 120-minute fire resistance, meeting the maintenance-free corrosion protection requirements over the full life cycle of bridge projects.

In bridge engineering, cast-in channels are core embedded components used to secure monitoring equipment, inspection facilities, protective ancillary facilities, overhead contact systems and power and communication equipment. Cast-in channels remain embedded in concrete or exposed to outdoor environments for long periods and are continuously subjected to moisture, acid and alkali media, salt spray corrosion and freeze-thaw cycles. If the corrosion protection process is inadequate, problems such as rusting, deformation and reduced load capacity are likely, directly affecting the service life and safety factor of the bridge project. This article comprehensively analyzes the corrosion protection requirements for bridge cast-in channels from the perspectives of the standards system, corrosion protection process requirements, testing standards and service life.

I. Corrosion protection standards system for bridge cast-in channels

The corrosion protection requirements for bridge cast-in channels are implemented in accordance with the following core standards:

1.1 TB/T 3329-2013 Cast-in Channels for Tunnel Overhead Contact Systems of Electrified Railways, and Amendment No. 1

This standard is administered by China Railway Electrification Bureau Group Co., Ltd. and came into effect on July 1, 2013. Amendment No. 1 was issued in September 2023, with the core changes including:

  • Material specifications: the materials for channels and anchor rods were changed toQ355B low-alloy steelor specific stainless steel

  • Upgraded welding process: the weld quality grade was changed from Grade I tono lower than Grade II

  • Added salt spray test requirement: hot-dip galvanized channels must pass the1,200-hour neutral salt spray test, and stainless steel channels are additionally subject to an intergranular corrosion test

  • Supplemented testing methods: a clause on chemical analysis by direct-reading spectrometry was added

1.2 Q/CR 749.3-2020 Protective Coatings and Paints for Railway Bridge Steel Structures and Components - Part 3: Auxiliary Steel Structures

This standard specifies the coating protection requirements for auxiliary steel structures of railway bridges (including cast-in channels). Cast-in channels should be treated for corrosion protection using Coating System No. 1; inspection items include appearance, diffusion layer thickness, anti-corrosion layer thickness, sealing layer adhesion, salt spray resistance (1200h) and damp heat resistance (1000h).

1.3 TB/T 3274-2011 Technical Conditions for Multi-Alloy Co-Diffusion Corrosion Protection of Railway Concrete Beam Accessories

This standard specifies the process requirements formulti-alloy co-diffusion corrosion protection technologyused for cast-in parts of railway concrete beams, and applies to metal accessories of concrete beams such as cast-in bolts and bearing anchors. High-speed railway cast-in parts are exposed for long periods to harsh environments involving mechanical vibration, impact, abrasion and outdoor high temperature, severe cold and high humidity; the use of this technology can effectively extend service life.

1.4 Other related standards

  • GB/T 37613-2019Cast-in Channel Sections - standard for sections used in channel products

  • GB/T 13912-2020Metallic Coatings - Technical Requirements and Test Methods for Hot-Dip Galvanized Coatings on Iron and Steel Articles

  • GB/T 10125-2021Corrosion Tests in Artificial Atmospheres - Salt Spray Tests - standard for salt spray test methods

II. Corrosion protection process requirements

The surfaces of cast-in channels and anchor rods should preferably usemulti-alloy co-diffusionorhot-dip galvanizingfor corrosion protection.

2.1 Hot-dip galvanizing process

When hot-dip galvanizing is used, cast-in channels and anchor rods should be implemented in accordance withGB/T 13912-2020andTB/T 2073.

  • Zinc coating thickness: the hot-dip galvanized coating thickness should be no less than80μm

  • Minimum average coating mass: no less than550g/m²

  • Salt spray test requirement: must pass the1,200-hour neutral salt spray test, and the protection rating should be no lower than Grade 7 of GB/T 6461

  • Welding requirement: once welded and fixed into groups, the whole assembly should be hot-dip galvanized for corrosion protection

In outdoor high-corrosion environments such as bridges, one can choosehot-dip galvanizing plus an epoxy resin composite coatingto further enhance corrosion protection. In actual projects, some bridge projects (such as Chizhou Bridge) require a zinc film thickness of no less than85μm。

2.2 Multi-alloy co-diffusion process

When multi-alloy co-diffusion is used, the following should be adopted in accordance with TB/T 3274:multi-alloy co-diffusion + insulating sealing layerfor corrosion protection:

  • Anti-corrosion layer thickness: no less than80μm

  • Insulation requirement: the sealing layer must meet the insulation requirement

The multi-alloy co-diffusion process is the recommended corrosion protection technology for high-speed railway cast-in parts, offering a hard coating and excellent corrosion resistance. Treated channels can reach3,000 hoursin the neutral salt spray test, with excellent mechanical properties, fire resistance and corrosion resistance.

2.3 Stainless steel material option

Given the complex environment of bridge piers, including river scour, salt spray corrosion and freeze-thaw cycles, channels shouldpreferably be made of high-strength stainless steelor hot-dip galvanized low-alloy steel. Stainless steel cast-in channels (such as 304/316 stainless steel) require no galvanizing and achieve corrosion protection through a dense chromium oxide passive film, making them suitable for high salt-spray corrosion environments such as coastal bridges.

III. Corrosion protection quality inspection requirements

The corrosion protection quality of bridge cast-in channels must be verified by the following inspections:

3.1 Zinc coating thickness inspection

Usea coating thickness gaugefor measurement, in accordance with TB/T 2074-2010. During inspection, measurement areas should be selected evenly at different parts of the channel body and T-head bolts, excluding interfering areas such as edges, welds and uneven spots. The hot-dip galvanized coating thickness on carbon steel should be no less than80μm, and stainless steel material should undergo an intergranular corrosion test.

3.2 Salt spray test

The salt spray test is the core inspection item for verifying corrosion protection performance. According to the requirements of TB/T 3329-2013 and Q/CR 749.3-2020:

  • Hot-dip galvanized channels: must pass the1,200-hour neutral salt spray test, with no red rust appearing on the specimen surface

  • Multi-alloy co-diffusion channels: can reach3,000 hoursor more in the neutral salt spray test

  • Testing standard: in accordance with GB/T 10125-2021 Corrosion Tests in Artificial Atmospheres - Salt Spray Tests

3.3 Incoming inspection and type testing

Incoming inspection batches for cast-in channels: when a supplier makes its first delivery, the first two inspection batches are15,000 meterscontrolled; subsequent inspections should be30,000 metersper inspection batch. Type testing should be carried out in any of the following cases:

  • New product finalizationstage

  • After formal production begins,structure, materials or processwhen there are significant changes that may affect product performance

  • Manufacturerresuming production after a shutdown of more than 1 yearupon resumption

  • Incoming inspection results differsignificantlyfrom the previous type test

  • Manufacturer'sfirst supplyoccasion

IV. Service life requirements

4.1 Same service life as the bridge structure (100 years)

Thecorrosion resistance of bridge cast-in channels should be equivalent to the service life of the bridge, and the required service life of a bridge in building terms isone hundred years. The channels should meet the corresponding bridgedesign service life of 100 yearsrequirement.

This means the corrosion protection system of the cast-in channels must be able to guaranteemaintenance-free or low-maintenanceoperation over the bridge's full life cycle (100 years). If the corrosion protection process is inadequate, the channels may develop severe rust within a few decades, and replacing channels embedded in concrete is almost impossible, resulting in huge safety risks and maintenance costs.

4.2 Comparison of service life for different corrosion protection processes

Corrosion protection processCoating/anti-corrosion layer thicknessSalt spray test durationEstimated service life
Hot-dip galvanizing≥80μm1,200 hours25-50 years
Hot-dip galvanizing + epoxy composite coatingat least 80μm + coatingat least 1,200 hours50-80 years
Multi-alloy co-diffusion + insulating sealing layer≥80μm3,000 hours100 years
Stainless steel (304/316)Natural passive filmIntergranular corrosion test100 years

4.3 Key factors affecting service life

The actual service life of cast-in channels is affected by the following factors:

  • Environmental corrosivity: coastal salt spray, industrial pollution and freeze-thaw cycles accelerate corrosion

  • Coating/anti-corrosion layer quality: thickness, uniformity and adhesion directly determine the protective effect

  • Construction quality: welding damage, coating damage and improper installation create initiation points for corrosion

  • Stray current: stray current in applications such as rail transit accelerates electrochemical corrosion

V. Daring corrosion protection solutions for bridge cast-in channels

5.1 Product advantages

Daring cast-in channels strictly comply with TB/T 3329-2013 and its Amendment No. 1, GB/T 37613-2019, Q/CR 749.3-2020 and other standards, and offer the following advantages:

  • Reliable materials: Q355 steel or 304/316 stainless steel, meeting the high durability requirements of bridge projects

  • Durable corrosion protection: hot-dip galvanizing for corrosion protection, with a zinc coating thickness of at least 80μm, meeting the 1,200-hour salt spray test requirement; a multi-alloy co-diffusion + insulating sealing layer process is also available

  • Multiple processes: available withwelded and rivetedprocess options

  • Comprehensive testing: passed numerous tests including 2-million-cycle fatigue and 120-minute fire resistance

  • Full life cycle: meets the corrosion protection requirement for a 100-year bridge design service life

5.2 Application scenarios

Daring cast-in channels are widely used in:

  • Railway bridges: embedment in bridge piers, overhead contact system masts and fixing of monitoring equipment

  • Highway bridges: fixing of auxiliary facilities and installation of inspection access

  • Cross-sea bridges: corrosion-protected anchoring in high salt-spray environments

  • Urban elevated structures: embedment for attached facilities such as crash barriers and sound barriers

VI. Frequently asked questions

Q1What is the zinc coating thickness requirement for bridge cast-in channels?
According to TB/T 3329-2013 and Amendment No. 1, the hot-dip galvanized coating thickness should be no less than 80μm. Some bridge projects (such as Chizhou Bridge) require a zinc film thickness of no less than 85μm. The multi-alloy co-diffusion anti-corrosion layer thickness should be no less than 80μm.
Q2What are the salt spray test requirements for cast-in channels?
Hot-dip galvanized channels must pass the 1,200-hour neutral salt spray test. Multi-alloy co-diffusion channels can reach more than 3,000 hours. Testing is based on GB/T 10125-2021.
Q3What is the design service life of bridge cast-in channels?
The design service life of bridge cast-in channels should be the same as that of the bridge structure, generally required to reach 100 years. The multi-alloy co-diffusion + insulating sealing layer process can meet the 100-year maintenance-free requirement.
Q4Which corrosion protection processes are available for bridge cast-in channels?
There are three main options: hot-dip galvanizing (at least 80μm), multi-alloy co-diffusion + insulating sealing layer (at least 80μm), and stainless steel. In highly corrosive environments, hot-dip galvanizing plus an epoxy resin composite coating may be selected.
Q5Are Daring cast-in channels suitable for bridge projects?
Yes. Daring cast-in channels strictly comply with TB/T 3329-2013, GB/T 37613-2019, Q/CR 749.3-2020 and other standards, are made of Q355 steel or 304/316 stainless steel, are available with welded or riveted processes, and meet the 100-year corrosion protection requirement for bridge projects.

Daring cast-in channels strictly comply with TB/T 3329-2013 and its Amendment No. 1 of 2023, GB/T 37613-2019, Q/CR 749.3-2020 and other standards. They are made of Q355 steel or 304/316 stainless steel and are available with welded or riveted processes. The products have passed numerous tests at the National Building Materials Testing Center, including 2-million-cycle fatigue and fire resistance, and are used with T-head bolts for flexible three-dimensional adjustment. For advice on selecting a corrosion protection solution for bridge cast-in channels in specific projects, please consult the Daring technical team.

References

Daring website - Welded cast-in channel product page

Daring website - Riveted cast-in channel product page

TB/T 3329-2013 Cast-in Channels for Tunnel Overhead Contact Systems of Electrified Railways, and Amendment No. 1

Q/CR 749.3-2020 Protective Coatings and Paints for Railway Bridge Steel Structures and Components - Part 3: Auxiliary Steel Structures

TB/T 3274-2011 Technical Conditions for Multi-Alloy Co-Diffusion Corrosion Protection of Railway Concrete Beam Accessories

GB/T 37613-2019 Cast-in Channel Sections

GB/T 13912-2020 Metallic Coatings - Technical Requirements and Test Methods for Hot-Dip Galvanized Coatings on Iron and Steel Articles

Back to Daring Home  Back to Top