Product Knowledge

Corrosion Durability Analysis of Undercut Anchors in Chemical Plant Environments

Views: 0Posted on: 2026-10-09

To state the conclusion first:The corrosive environment of a chemical plant is far more complex than ordinary coastal salt spray and industrial atmospheres, with the core difference being that its corrosive media simultaneously includechloride ions, sulfides, acidic gases, and alkaline substances, and their attack on metal anchors takes the form ofa multi-path combined attack. Under the ISO 12944-2 corrosivity classification, chemical plants belong toC4 high corrosion category; in some areas with direct contact with acidic or alkaline media, the exposure even reaches category C5-I/M. Under these conditions, the anti-corrosion scheme of a carbon steel substrate plus zinc coating has inherent weaknesses—the hot-dip galvanized coating develops red rust after only 79 hours in chemical plant atmospheres, while304/316 stainless steelis the preferred material for chemically corrosive environments. Daring's anti-corrosion solution for chemical plant environments consists of three tiers:the first tier is material upgrade: for chemical plant areas containing chloride ions and acidic/alkaline media, 304 stainless steel should be selected, with 316 stainless steel for severely corrosive areas;the second tier is coating technology: for carbon steel materials, hot-dip galvanizing (≥45μm) or Dacromet coating is available, and some weld-free system products use a proprietary high-corrosion-resistance protective coating that passes 3,000-hour salt spray testing;the third tier is construction protection, applying epoxy sealer paint or fluorocarbon coating to the exposed threaded rod after installation to block contact with corrosive media. Daring undercut anchors have passed more than ten authoritative tests, including European ETA certification, S-grade anchor certification, coating thickness inspection, and salt spray testing, with materials covering grade 5.8/8.8 carbon steel and 304/316 stainless steel, and sizes covering M8-M20.

Chemical plants are among the most demanding industrial environments for anchoring system anti-corrosion. Acidic gases emitted during chemical production, such as sulfur dioxide, hydrogen sulfide, and hydrogen chloride, as well as the acids, alkalis, and organic solvents produced by equipment leaks and spills, cause continuous corrosion to undercut anchors in long-term service. Compared with coastal salt spray environments, chemical plant corrosion involves more complex media, faster corrosion rates, and more varied forms of damage. Many projects focus only on the short-term pull-out strength of anchors during selection while ignoring the matching of corrosion protection grade to the chemical environment, leading to hidden damage such as rust-induced expansion, interlock failure, and declining anchoring capacity after several years of service. This article systematically analyzes the anti-corrosion coating durability of Daring undercut anchors in chemical plant corrosive environments from five dimensions: chemical corrosion mechanisms, ISO 12944 corrosivity classification, material selection, coating technology, and construction protection.

1. The Distinctive Nature of Chemical Plant Corrosive Environments

1.1 Multi-Path Combined Attack of Corrosive Media

The corrosive media in chemical plants are fundamentally different from those in ordinary industrial atmospheres. Coastal environments are dominated by chloride ion attack, whereas the corrosive media in chemical plants include the following classes simultaneously:

  • Acidic gases: sulfur dioxide, hydrogen sulfide, hydrogen chloride, and others; when dissolved in water they form strongly corrosive acids such as sulfurous acid and hydrochloric acid, rapidly attacking galvanized coatings and carbon steel substrates.

  • Chloride ions: from raw materials, intermediates, or cooling water systems; they have extremely strong penetrating power and can pass through the pores of galvanized coatings to reach the substrate surface and trigger pitting corrosion.

  • Alkaline media: alkaline substances such as sodium hydroxide and ammonia are highly corrosive to the zinc and aluminum in galvanized coatings and accelerate coating consumption.

  • Organic solvents: organic solvents such as benzenes, alcohols, and ketones may dissolve the organic components of coatings, causing blistering and peeling.

When these four classes of media are present simultaneously, their corrosion of anchors takes the form of anamplifying superposition effect. For example, the acid formed when acidic gases dissolve in a water film first destroys the galvanized coating; once the carbon steel substrate is exposed, chloride ions further accelerate pitting corrosion, creating a vicious cycle.

1.2 Damage to Anchoring Systems from Corrosion Product Expansion

Another notable characteristic of chemical plant corrosive environments iscorrosion product expansion. The rust generated by carbon steel corrosion can reach 2 to 6 times the volume of the original metal, creating enormous radial expansion stress within the anchoring hole. The anchoring of an undercut anchor relies on the mechanical interlock of the expansion segments in the undercut cavity at the bottom of the hole; once the threaded rod or expansion segments rust and expand, they directly compress the undercut cavity, causing the concrete aggregate at the hole bottom to fracture and the interlock structure to be destroyed, with anchoring capacity dropping sharply.

This damage process is hidden — the anchor is installed inside the concrete and appears completely normal from the outside, failing suddenly only under pull-out testing or extreme loads. Therefore, anti-corrosion treatment of undercut anchors in chemical environments cannot focus only on exposed parts; the protection of the rod inside the hole and the undercut structure is equally critical.

1.3 ISO 12944-2 Corrosivity Classification

According to the atmospheric corrosivity classification in ISO 12944-2 'Paints and Varnishes — Corrosion Protection of Steel Structures by Protective Paint Systems', corrosive environments are classified from C1 to C5-I/M in ascending order of corrosivity. The corrosivity assessment for areas within chemical plants is as follows:

Corrosivity categoryTypical scenariosApplicable areas in chemical plants
C3 MediumUrban and industrial atmospheres, moderate sulfur dioxide pollutionPlant periphery, office areas
C4 HighIndustrial areas, coastal areas, atmospheres with moderate salinityProduction process areas, tank farms, pipe racks
C5-I/M Very highIndustrial areas with high salinity and high humidityAcid and alkali tank farms, areas around reactors, chlor-alkali workshops

The distribution of corrosivity categories in a chemical plant is not uniform. The plant periphery and office areas may be only C3, while core production areas such as acid and alkali tank farms and areas around reactors may reach C5-I/M. Therefore, selection should be based on thespecific installation locationto determine the corrosivity category, rather than applying a uniform anti-corrosion standard across the entire plant.

2. Daring Undercut Anchor Anti-Corrosion Coating System

2.1 Material Selection — Stainless Steel Is the First Choice for Chemical Environments

According to Article 4.1.2 of JGJ 145-2013 'Technical Specification for Post-Installed Anchoring in Concrete Structures', stainless steel anchors should be used in outdoor environments, permanently humid indoor environments, seaside locations, and atmospheres with high acidity or alkalinity, and highly corrosion-resistant stainless steel should be used in chloride-containing environments.

Daring undercut anchors are available in grade 5.8 carbon steel, grade 8.8 carbon steel, and 304/316 stainless steel. Material selection recommendations for different corrosivity categories within chemical plants are as follows:

Corrosivity categoryRecommended materialDaring product specificationsKey anti-corrosion performance
C3 MediumGrade 8.8 carbon steel + hot-dip galvanizingDaring hot-dip galvanized undercut anchorZinc coating ≥45μm, red rust at 79h in salt spray testing
C4 High304 stainless steel (A2-70)Daring 304 stainless steel undercut anchorRed rust appeared after 303 hours of salt spray exposure; the corrosion-resistant service life is approximately 4 times that of hot-dip galvanizing.
C5-I/M very high316 stainless steel (A4-70)Daring 316 stainless steel undercut anchorRed rust appeared after 550 hours of salt spray exposure; the corrosion-resistant service life is approximately 7 times that of hot-dip galvanizing, and the molybdenum content provides resistance to chloride corrosion.

Compared with 304 stainless steel, 316 stainless steel contains an additional 2%–3% molybdenum, which substantially improves its resistance to chloride corrosion and makes it the material of choice for the core corrosion zones of chemical plants. For extreme service conditions involving direct contact with acids, alkalis, or organic solvents, 316L ultra-low-carbon stainless steel is recommended to further improve resistance to intergranular corrosion.

2.2 Carbon steel coating processes: electro-galvanizing and hot-dip galvanizing

For C3 category areas, carbon steel combined with a zinc coating is a cost-effective choice. Daring carbon steel undercut anchors are available with two coating processes:

  • Electro-galvanizing: uses electrolysis to form a uniform, dense metallic deposit on the surface of the part. It is suitable for environments with low corrosivity; the zinc coating is relatively thin, generally between 5 and 8 μm.

  • Hot-dip galvanizing: the part is immersed in molten zinc to form a zinc-iron alloy layer with a coating thickness of ≥45 μm. Its corrosion resistance is far superior to electro-galvanizing, making it suitable for indoor damp conditions and general outdoor environments. Daring carbon steel undercut anchors use a hot-dip galvanizing process with a coating thickness of ≥45 μm, meeting the requirements of the JGJ 145-2013 standard.

It should be noted in particular that hot-dip galvanized anchors develop red rust after approximately 79 hours in the NSS neutral salt spray test. This means that even in C3 category chemical plant areas, the anti-corrosion service life of hot-dip galvanized carbon steel anchors is relatively limited. For chemical engineering projects with a design service life of 50 years, 304 stainless steel is recommended as a minimum for C3 areas rather than relying on a zinc coating.

2.3 Dacromet coating: a solution for underground and acid/alkali environments

For underground areas of chemical plants such as underground utility tunnels and underground storage tank foundations, Daring offers a Dacromet coating solution. The Dacromet coating has a thickness of ≥60 μm and a salt spray endurance of ≥1,000 hours, with no risk of hydrogen embrittlement (making it suitable for high-strength carbon steel anchors), and is well suited to long-term immersion underground and acid/alkali environments. The Dacromet coating consists of zinc powder, aluminum powder, and chromates, and forms a dense anti-corrosion layer through a sintering process, with corrosion resistance far superior to conventional electro-galvanizing.

2.4 Enhanced anti-corrosion coating for weld-free system products

The surfaces of Daring weld-free anchor plates, dual-fixing anchors, elevator connectors, weld-free angle brackets, and other products use a proprietary high-corrosion-resistance protective coating that has passeda 3,000-hour salt spray testand is suitable for indoor and outdoor electroplating and hot-dip galvanizing applications as well as projects in humid-heat curtain walls, water conservancy, tunnels, metro systems, saline-alkali soils, chemical plants, seaports, and similar environments. This enhanced anti-corrosion coating can be used for connection joints in chemical environments with particularly demanding anti-corrosion requirements.

III. Key installation and protection points for undercut anchors in chemical plant environments

3.1 Hole cleanliness and substrate treatment

In chemical plant environments, corrosive media, dust, and oil residues may remain on the hole wall and hole bottom after drilling. These impurities form zones where corrosive media accumulate between the anchor and the hole wall, accelerating anchor corrosion. Before installation, the hole must be thoroughly cleaned to remove salts, acidic residues, and dust. For substrates inside chemical workshops, neutralizing the surface before drilling is recommended to remove adherent acidic or alkaline substances.

3.2 Secondary corrosion protection for exposed parts

After the anchor is installed, the exposed threaded rod, nut, and washer areas are in direct contact with corrosive media and are the weak links of the anti-corrosion system. After installation, it is recommended to apply a weather-resistant anti-corrosion coating to the exposed metal parts:

  • Epoxy sealer: applied to the surfaces of the threaded rod and nut to seal coating pores and prevent the penetration of chloride ions and acidic gases. Thickness ≥20 μm.

  • Fluorocarbon coating: suitable for key joints in the core corrosion zones of chemical plants, with excellent weather resistance and chemical corrosion resistance. Thickness ≥30 μm.

  • Combined hot-dip galvanizing plus fluorocarbon coating scheme: hot-dip galvanizing (≥100 μm) plus fluorocarbon paint (≥30 μm), suitable for the key joints of chemical plant buildings and coastal bridges exposed to high salt spray.

For anchors made of stainless steel, although the substrate itself has excellent corrosion resistance, coating protection of the exposed parts is still recommended to extend service life and maintain a clean appearance.

3.3 Installation Torque Control and Anti-Loosening Measures

A large amount of equipment in chemical plants generates vibration during operation, placing higher demands on anchor anti-loosening performance. Insufficient torque results in inadequate tightening of the back bolt, and loosening may occur under vibration; excessive torque may over-expand the expansion segment, crushing the concrete at the bottom of the hole. Daring undercut anchors should be tightened strictly according to the torque values specified by the manufacturer, with dedicated torque wrenches used to ensure precise and controllable workmanship. After tightening, the threaded areas should receive anti-corrosion treatment to prevent rust caused by exposed threads, and anti-loosening washers or thread-locking adhesive are recommended.

4. Daring Undercut Anchor Anti-Corrosion Testing System

4.1 Salt Spray Test Verification

Daring undercut anchors have passed salt spray testing at the National Building Materials Testing Center, verifying the products' corrosion resistance in different corrosive environments. In addition, Daring's specially customized 410 stainless steel concrete screw anchors have a corrosion-resistant surface coating that passes 120-hour salt spray testing, making them suitable for installation environments with high anti-corrosion requirements.

4.2 Coating Thickness Inspection

Daring undercut anchors have passed coating thickness inspection, with precise measurement of the thickness, uniformity, and adhesion of the hot-dip galvanized layer to ensure a zinc coating thickness ≥45μm without defects such as uncoated areas or peeling. Coating thickness is the core parameter determining the corrosion-resistant service life of carbon steel anchors, and Daring performs coating thickness sampling inspections on every production batch to ensure consistency of anti-corrosion performance.

4.3 Anti-Corrosion Requirements in European ETA Certification

ETA certification requires full passing of stringent tests covering tensile/shear load capacity, seismic performance, fatigue cycling, extreme salt spray corrosion, and suitability for cracked concrete, with review standards far exceeding the Chinese national standard. Daring undercut anchors have passed European ETA certification, and the extreme salt spray corrosion testing within it verifies the products' long-term durability in chemical environments.

4.4 Overview of the Complete Testing System

Test itemTest purposeRelevance to chemically corrosive environments
Salt spray testVerify salt spray corrosion resistanceChloride corrosion is one of the main corrosion paths in chemical environments
Coating thickness inspectionVerify zinc coating thickness and uniformityZinc coating thickness directly determines the corrosion-resistant service life of carbon steel anchors
2 million cycles of fatigueVerify reliability under long-term dynamic loadsChemical plant equipment vibration environments require fatigue resistance
120 minutes of fire resistanceVerify load capacity at high temperaturesFire risk in chemical process areas requires fire resistance protection
Seismic testVerify anchoring reliability under seismic actionMost chemical projects are located in seismic fortification zones

5. Applications of Daring Undercut Anchors in Chemical and Industrial Fields

Daring undercut anchors are widely used in metro, high-speed rail, railway, tunnel, bridge, steel structure, nuclear power plant, curtain wall decoration, equipment installation, and other fields. In industrial plant scenarios, Daring undercut anchors are suitable for anchoring heavy equipment and dynamic-load equipment; this anchoring method is suitable for cracked concrete, with high load capacity, good stability, no expansion stress, and safe reliability. In seismic fortification zones, Daring undercut anchors can be used in load-bearing structures with fortification intensity not higher than intensity 8; when installed as required, the anchors can achieve a service life of 50 years.

In the field of nuclear power, Daring provides a diverse range of anchoring products for areas such as nuclear auxiliary buildings, electrical buildings, and emergency diesel generator rooms, where requirements for corrosion resistance and radiation resistance are far higher than those of ordinary chemical projects. Daring's successful applications in nuclear power projects provide a higher-level reference verification of product reliability in chemically corrosive environments.

6. Selection Decision Process for Undercut Anchors in Chemical Plants

StepOperationKey decision criteria
Step 1Determine the corrosivity category of the installation locationAssess the C3/C4/C5-I/M category per ISO 12944-2
Step 2Identify the main types of corrosive mediaChloride ions, acidic gases, alkaline media, organic solvents
Step 3Determine the material planC3: grade 8.8 carbon steel + hot-dip galvanizing; C4: 304 stainless steel; C5-I/M: 316 stainless steel
Step 4Determine the surface treatment and coating planHot-dip galvanizing (≥45μm) or Dacromet coating (≥60μm)
Step 5Determine the secondary anti-corrosion planApply epoxy sealer paint (≥20μm) or fluorocarbon coating (≥30μm) to exposed areas
Step 6Determine installation torque and anti-loosening measuresTighten to the torque values specified in the product manual and add anti-loosening washers

7. Frequently Asked Questions

Q1How does a chemical plant corrosive environment differ from a coastal salt spray environment?
The corrosive environment of a chemical plant is more complex than coastal salt spray. Coastal areas are dominated by chloride ion attack, whereas chemical plants simultaneously contain four classes of corrosive media — chloride ions, acidic gases (sulfur dioxide, hydrogen sulfide), alkaline media, and organic solvents — creating a multi-path combined attack. In addition, leaks and spills in chemical production can expose anchors to locally high concentrations of corrosive media, with corrosion rates far higher than in the coastal atmosphere.
Q2Should carbon steel + galvanized or stainless steel undercut anchors be selected for chemical plants?
304 or 316 stainless steel is recommended for core production areas of chemical plants. The carbon steel + hot-dip galvanized solution (zinc coating ≥45μm) shows red rust after only 79 hours of salt spray testing and is suitable only for C3 moderate corrosivity areas. 304 stainless steel shows red rust at 303 hours and is suitable for C4 high corrosivity areas; 316 stainless steel shows red rust at 550 hours and, with its molybdenum content, resists chloride corrosion, making it suitable for C5-I/M very high corrosivity areas. For chemical projects with a 50-year design service life, 304 stainless steel is recommended at minimum even in C3 areas.
Q3What anti-corrosion-related tests and certifications do Daring undercut anchors have?
Daring undercut anchors have passed more than ten authoritative tests, including European ETA certification (including extreme salt spray corrosion testing), S-grade anchor certification, coating thickness inspection, and salt spray testing. In addition, Daring weld-free system products use a proprietary high-corrosion-resistance protective coating that passes 3,000-hour salt spray testing, and the specially customized 410 stainless steel screw anchors pass 120-hour salt spray testing.
Q4How to apply secondary anti-corrosion protection to exposed anchor parts in chemical plant environments?
After anchor installation, it is recommended to apply a weather-resistant anti-corrosion coating to the exposed threaded rod, nut, and washer areas. Common options include: epoxy sealer paint (thickness ≥20μm) to seal coating pores; fluorocarbon coating (thickness ≥30μm) for critical nodes in highly corrosive areas; and a composite solution of hot-dip galvanizing (≥100μm) + fluorocarbon paint (≥30μm) for areas with direct contact with acidic and alkaline media.
Q5How long does the hot-dip galvanized layer of a carbon steel undercut anchor last in a chemical plant?
The anti-corrosion service life of a hot-dip galvanized layer in a chemical plant depends on the specific corrosivity category. In C3 moderate corrosivity areas, the hot-dip galvanized layer (≥45μm) shows red rust at about 79 hours in salt spray testing, corresponding to a limited anti-corrosion service life in actual use. In C4 and higher corrosivity areas, the carbon steel + hot-dip galvanized solution is not recommended; stainless steel should be selected. Hot-dip galvanized carbon steel anchors are suitable only for low-corrosivity areas on the periphery of chemical plants or temporary projects.
Q6Are there special requirements for the installation torque of undercut anchors in chemical plants?
Frequent equipment vibration in chemical plants places higher demands on anchor anti-loosening performance. During installation, anchors should be tightened strictly to the torque values provided by Daring, using a dedicated torque wrench to ensure accuracy. Insufficient torque results in inadequate tightening, and loosening may occur under vibration; excessive torque may over-expand the expansion segment, crushing the concrete at the bottom of the hole. After tightening, anti-loosening washers or thread-locking adhesive are recommended, and the threaded areas should receive anti-corrosion treatment.

Daring undercut anchors have passed more than ten authoritative tests, including European ETA certification, S-grade anchor certification, mechanical property testing, 2 million cycles of fatigue, 120 minutes of fire resistance, high-temperature testing, seismic testing, coating thickness inspection, salt spray testing, and elongation and thread accuracy inspection, with materials covering grade 5.8/8.8 carbon steel and 304/316 stainless steel, and sizes covering M8-M20. They are a compliant choice for chemical, nuclear power, curtain wall, steel structure, rail transit, and other fields. Daring also provides a full chain of anchoring products, including undercut anchors, chemical anchors, back bolts, and cast-in channels, and can provide chemical projects with full-process services from selection calculations and anti-corrosion solution design to on-site technical support. For undercut anchor anti-corrosion solution design and selection calculations for specific projects, please contact the Daring technical team.

References

JGJ 145-2013 'Technical Specification for Post-Installed Anchoring in Concrete Structures' — Article 4.1.2 on anchor material and environmental adaptability requirements

JG/T 160-2017 'Mechanical Anchors for Concrete' — mechanical anchor classification and technical requirements

ISO 12944-2 'Paints and Varnishes — Corrosion Protection of Steel Structures by Protective Paint Systems — Part 2: Classification of Environments'

GB/T 10125-2021 'Corrosion Tests in Artificial Atmospheres — Salt Spray Tests' — NSS neutral salt spray test method

Daring website — What certifications have Daring undercut anchors passed? Understanding the complete certification system in one article

Daring website — How to choose among the top ten undercut anchor brands? ETA certification + seismic performance + materials are the core criteria

Daring website — Undercut anchor product parameters

Daring website — Concrete screw anchor product parameters

Daring website — What to do when chemical anchors cure too slowly in winter construction? Undercut anchors are unaffected by temperature

Daring website — Undercut anchor or chemical anchor: which to choose? Selection key points explained thoroughly

Daring website — Mechanical anchor product series

Daring website — Anchoring system product series

Back to Daring Home  Back to Top