To state the conclusion first:For chemical anchor anti-corrosion in coastal areas with heavy salt spray, the core principle ismaterial selection takes priority over coating protection. In chloride-containing salt spray environments,a carbon steel substrate + galvanized coatingsolution has inherent shortcomings — NSS neutral salt spray test data show that hot-dip galvanized chemical anchors show red rust after only 79 hours; by contrast,316 stainless steel (A4-70)with its additional 2%-3% molybdenum content, offers greatly improved resistance to chloride corrosion, shows red rust only after 550 hours in salt spray testing, and has a corrosion-resistant service life of aboutmore than 7 times that of hot-dip galvanizing. Daring's anti-corrosion solution for coastal areas with heavy salt spray consists of three tiers:the first tier is material upgrade: 316 stainless steel is required for chloride-containing environments, while 304 stainless steel is suitable for general coastal environments;the second tier is adhesive matching, paired with the Daring DL-200E modified epoxy injection anchoring adhesive, which offers waterproof and water-tolerant performance and wet-surface bonding capability, making it suitable for high-moisture substrates in coastal areas;the third tier is construction protection, carrying out enhanced hole cleaning to remove salt and dirt from the hole, and applying a weather-resistant anti-corrosion coating to the exposed threaded rod after installation to block salt spray contact. Daring products have been validated in coastal projects with heavy corrosion, such as the Fujian Zhangzhou Nuclear Power Plant and Guangzhou International Finance Center.
Coastal areas suffer constant erosion from heavy salt spray, and the chloride ions carried in the air have extremely strong penetrating power, causing continuous corrosion to the metal components of anchoring systems. As key components connecting structures such as curtain walls and equipment foundations, the anti-corrosion treatment of chemical anchors directly affects the safety assurance of the anchoring system's 50-year design service life. However, many projects focus only on the short-term pull-out strength of anchors during selection while ignoring the matching of corrosion protection grade to the service environment, leading to hidden damage such as rust-induced expansion, adhesive layer tearing, and anchoring failure after several years of service. This article systematically analyzes Daring's anti-corrosion solution for chemical anchors in coastal areas with heavy salt spray from four dimensions: corrosion mechanism, material selection, adhesive matching, and construction protection.
1. Corrosion Mechanism of Heavy Salt Spray Coastal Environments on Chemical Anchors
1.1 Chloride Ion Attack — The Primary Culprit of Salt Spray Corrosion
The salt spray in the coastal atmosphere consists mainly of sodium chloride, and chloride ions have extremely strong penetrating power, able to pass through the passivation film on metal surfaces and the pores of galvanized coatings to reach the substrate and trigger pitting corrosion. For carbon steel anchors, even with a galvanized coating, chloride ions can still penetrate through tiny coating pores, edges, and thread roots, triggering localized electrochemical corrosion. The volume of corrosion products (rust) can expand to2 to 6 timesthat of the original metal; the resulting expansion stress creates radial compression at the anchoring interface, tearing the adhesive bond layer and causing anchoring capacity to decline gradually until it is completely lost.
1.2 Wet-Dry Cycling — A Catalyst That Accelerates Corrosion
The wet-dry alternation caused by day-night temperature differences in coastal areas accelerates the electrochemical corrosion process on anchor surfaces. During the wet phase, salt spray forms an electrolyte film on the anchor surface; during the dry phase, salts concentrate, chloride ion concentration rises, and the corrosion rate increases further. This cyclic corrosion effect is especially pronounced on exposed anchor threaded rods and nuts.
1.3 Hidden Damage — The Gradual Path to Anchoring Failure
Unlike the visible corrosion of curtain wall panels, corrosion of chemical anchors is mostly hidden damage. After an anchor is installed in a hole, most of the threaded rod is wrapped in adhesive and concrete, and corrosion begins in invisible areas. Once the threaded rod rusts and expands, the first damage occurs at the bond interface between the adhesive and the rod; the decline in anchoring capacity may continue for years without visible external anomalies, and under extreme wind loads or seismic action, the anchoring system may fail suddenly.
2. Material Selection — The First Line of Defense for Anti-Corrosion
2.1 Regulatory Basis: Environmental Adaptability Requirements of JGJ 145-2013
According to Article 4.1.2 of JGJ 145-2013 'Technical Specification for Post-Installed Anchoring in Concrete Structures', metal anchors should be given corrosion protection appropriate to the environmental exposure class. Stainless steel anchors should be used in outdoor environments, permanently humid indoor environments, seaside locations, and atmospheres with high acidity or alkalinity,and highly corrosion-resistant stainless steel should be used in chloride-containing environments. The standard's anti-corrosion requirement for the surface of chemical anchor rods is: they must undergohot-dip galvanizing of 45μmor a special coating treatment with anti-corrosion capability superior to 45μm hot-dip galvanizing, to ensure that the rebar embedded in the structure does not rust.
This provision makes two key points clear: first, ordinary carbon steel anchors in coastal environments must undergo galvanizing treatment as a minimum; second, chloride-containing coastal environments with heavy salt spray have exceeded the effective protection range of galvanized coatings, and highly corrosion-resistant stainless steel must be used.
2.2 Comparison of Material Corrosion Resistance — Salt Spray Test Data
The following are comparative data from NSS neutral salt spray tests, showing differences in the corrosion resistance of chemical anchors made of different materials:
| Material type | Time to white rust | Time to red rust | Corrosion resistance class | Applicable environment |
|---|---|---|---|---|
| Electro-galvanized chemical anchor | 18 hours | 42 hours | Low | Indoor dry environments |
| Hot-dip galvanized chemical anchor | 53 hours | 79 hours | Moderate | Humid indoor and general outdoor environments |
| 304 stainless steel (A2-70) | — | 303 hours | High | Outdoor exposed and humid environments |
| 316 stainless steel (A4-70) | — | 550 hours | Very high | Coastal areas with heavy salt spray and chemically corrosive environments |
Data interpretation: hot-dip galvanized chemical anchors show red rust at 79 hours, while 304 stainless steel does not until 303 hours, and 316 stainless steel reaches 550 hours. The corrosion-resistant service life of 316 stainless steel is about7 times that of hot-dip galvanizing, and that of 304 stainless steel is about4 times。
2.3 Material Selection Decisions for Different Coastal Zones
| Coastal zone classification | Distance from coastline | Recommended material | Daring product model |
|---|---|---|---|
| Nearshore light salt spray zone | More than 5km from the coastline | 304 stainless steel (A2-70) | Daring 304 stainless steel chemical anchor |
| Coastal heavy salt spray zone | Within 5km of the coastline | 316 stainless steel (A4-70) | Daring 316 stainless steel chemical anchor |
| Splash zone / tidal zone | Direct contact with seawater | 316L stainless steel (ultra-low carbon) | Daring 316L stainless steel series |
Daring chemical anchors are available in two stainless steel materials, 304 (A2-70) and 316 (A4-70). The 316 stainless steel contains an additional 2%-3% molybdenum, greatly improving resistance to chloride corrosion. For extreme conditions with direct seawater contact, such as splash zones and tidal zones, 316L ultra-low carbon stainless steel is recommended to further improve resistance to intergranular corrosion.
3. Adhesive Matching — The Second Line of Defense for Anti-Corrosion
3.1 Special Requirements for Anchoring Adhesives in Coastal Environments
In coastal areas with heavy salt spray, salt and moisture may remain on the inner wall of the anchoring hole. When ordinary anchoring adhesives cure on such substrates, their bond strength drops significantly. DaringDL-200E modified epoxy injection anchoring adhesiveis a product meeting the national Grade A adhesive standard, specially formulated to providewaterproof and water-tolerant performanceandwet-surface bonding capability; even when a water film is present on the hole wall, the adhesive can still form an effective bond with the concrete hole wall.
The modified epoxy resin system of DL-200E has high viscosity and thixotropy, maintaining a stable adhesive form in humid environments. The product is suitable for dry holes, holes with condensation moisture, water-filled holes, underwater post-installed rebar, tidal zones, and other conditions, providing a complete construction solution for post-installed rebar in coastal environments.
3.2 Interface Compatibility Between Adhesive and Anchor Coating
The load capacity of a chemical anchor depends not only on the strength of the anchoring adhesive itself; theinterface bondingbetween the adhesive and the metal rod is the critical surface for load transfer. If the adhesive reacts chemically with the rod coating or the interface debonds, adhesive-steel interface peeling may still occur under pull-out loads even when the concrete substrate is intact and the adhesive strength is sufficient, causing premature failure of the anchoring point. Interface compatibility issues are especially prominent in humid, salt-spray coastal conditions.
Daring recommends using the DL-200E anchoring adhesive together with Daring chemical anchors. Daring has systematically tested the compatibility between the adhesive and rod coatings to ensure stable and reliable interface bond performance. If adhesives from other brands are to be used, interface compatibility verification testing should be performed.
4. Construction Protection — The Third Line of Defense for Anti-Corrosion
4.1 Enhanced Hole Cleaning — Removing Salt and Dirt
In coastal environments, salt, dust, and dirt may remain on the hole wall and bottom after drilling. These impurities form an isolation layer between the adhesive and the hole wall, severely affecting bond performance. Installation with the Daring DL-200E anchoring adhesive must strictly followthe three-brush, three-blow procedureHole cleaning procedure: blow out dust → brush the hole → blow out dust → brush the hole → blow out dust, repeating until no dust escapes from the hole. When blowing, the air tube should be inserted to the bottom of the hole to ensure that dust and salt at the bottom are completely blown out.
For high-altitude, windy environments, the hole mouth should be sealed with dustproof tape immediately after cleaning to prevent secondary dust contamination of the hole wall. Poor hole cleaning is the leading cause of failed pull-out tests, and in coastal environments the cleaning procedure must never be omitted or simplified.
4.2 Enhanced Anti-Corrosion Coating for Exposed Threaded Rods
After anchor installation, the exposed threaded rod, nut, and washer areas are the weak points for salt spray corrosion. After installation, it is recommended to applya weather-resistant anti-corrosion coatingto the exposed metal areas to block direct contact between salt spray and the metal surface. Common anti-corrosion coating options include:
Epoxy sealer paint: applied to the surfaces of the threaded rod and nut to seal coating pores and prevent chloride ion penetration. Thickness ≥20μm.
Fluorocarbon coating: suitable for critical nodes in areas with heavy salt spray and severe corrosion, with excellent weather resistance and corrosion resistance. Thickness ≥30μm.
Zinc-based sealer: used together with hot-dip galvanized coatings to fill pores in the zinc layer and improve salt spray resistance.
For anchors made of stainless steel, although the base material itself offers excellent corrosion resistance, coating protection is still recommended for exposed areas to extend service life and keep the appearance clean.
4.3 Installation Torque Control and Anti-Loosening Measures
Chemical anchors in coastal areas with heavy salt spray also require particular attention to installation torque control. Torque that is too high or too low will affect anchoring quality. Meanwhile, anchors in wind-vibration environments should be fitted with anti-loosening washers or use thread-locking adhesive to prevent nut loosening from long-term vibration. After tightening, the threaded areas should receive anti-corrosion treatment to prevent rust caused by exposed threads.
5. Summary of the Three-Tier Protection System in Daring's Coastal Anti-Corrosion Solution
| Protection tier | Protective measures | Daring product/solution | Key performance indicators |
|---|---|---|---|
| Tier 1 | Material upgrade | 316 stainless steel chemical anchor (A4-70) | 550h to red rust in salt spray testing, with a corrosion-resistant service life about 7 times that of hot-dip galvanizing |
| Tier 2 | Adhesive matching | DL-200E modified epoxy injection anchoring adhesive | National Grade A adhesive standard, waterproof and water-tolerant, wet-surface bonding |
| Tier 3 | Construction protection | Enhanced hole cleaning + coatings for exposed parts + anti-loosening measures | Three-brush, three-blow cleaning; epoxy sealer paint / fluorocarbon coating |
Daring's anti-corrosion solution for chemical anchors in coastal areas with heavy salt spray has been validated in multiple major projects. Daring products are used in theFujian Zhangzhou Nuclear Power Plantproject, which is located in the coastal area of Zhangzhou, Fujian Province, and is the first coastal site in Fujian approved under third-generation AP1000 nuclear power technology. Daring Anka anchors use an Otis plate design for better load-bearing performance and are available in 304/316 stainless steel to meet the anti-corrosion requirements of nuclear power projects. The Daring back bolt system has also been applied toGuangzhou International Finance Center(main tower 440.75m tall),Shanghai Towerand other super-high-rise landmark projects. The products offer strong weather resistance and excellent suitability for coastal environments with heavy salt spray corrosion.
Daring products hold an important position in core fields such as high-end curtain walls, rail transit, utility tunnels and industry, bridges and tunnels, nuclear power, and marine engineering. Daring has a well-established supply chain management system and quality assurance system, and can provide projects in coastal areas with heavy salt spray with full-process services ranging from product selection and supply assurance to on-site technical support. For anti-corrosion solution design and selection calculations for chemical anchors on specific projects, please contact the Daring technical team.
6. Frequently Asked Questions
| Q1 | Why can't hot-dip galvanized chemical anchors be used in coastal areas with heavy salt spray? Hot-dip galvanized chemical anchors show red rust after only 79 hours in NSS neutral salt spray testing, and their zinc coating offers limited protection against chloride ions. Chloride ions in coastal salt spray can penetrate the pores of the zinc coating and reach the carbon steel substrate, triggering pitting corrosion. The volume expansion of corrosion products tears the adhesive bond layer, causing anchoring capacity to gradually decline. JGJ 145-2013 explicitly requires the use of highly corrosion-resistant stainless steel in chloride-containing environments. |
| Q2 | Should 304 or 316 stainless steel be selected for coastal areas? 304 stainless steel (A2-70) can be selected for nearshore areas with light salt spray more than 5km from the coastline; its salt spray red rust time is about 303 hours, with a corrosion-resistant service life about 4 times that of hot-dip galvanizing. For heavy salt spray coastal areas within 5km of the coastline, 316 stainless steel (A4-70) must be selected; with an additional 2%-3% molybdenum content, its salt spray red rust time reaches 550 hours, and its resistance to chloride corrosion is greatly improved. |
| Q3 | What advantages does the Daring DL-200E anchoring adhesive offer in coastal environments? As a product meeting the national Grade A adhesive standard, DL-200E offers waterproof and water-tolerant performance and wet-surface bonding capability, forming an effective bond even when a water film is present on the hole wall. Its modified epoxy resin system has high viscosity and thixotropy and is suitable for dry holes, holes with condensation moisture, water-filled holes, underwater post-installed rebar, tidal zones, and other conditions, providing a complete construction solution for post-installed rebar in coastal environments. |
| Q4 | Are there special requirements for hole cleaning when installing chemical anchors in coastal environments? In coastal environments, salt, dust, and dirt may remain on the hole wall after drilling, so the three-brush, three-blow cleaning procedure must be strictly followed. When blowing, the air tube should be inserted to the bottom of the hole to ensure that dust and salt at the bottom are completely blown out. In high-altitude, windy environments, the hole mouth should be sealed with dustproof tape immediately after cleaning to prevent secondary dust contamination of the hole wall. |
| Q5 | What anti-corrosion treatment is needed for exposed threaded rods after anchor installation? It is recommended to apply a weather-resistant anti-corrosion coating to the exposed threaded rod, nut, and washer areas to block direct contact between salt spray and the metal surface. Common coating options include epoxy sealer paint (thickness ≥20μm) and fluorocarbon coating (thickness ≥30μm), suitable for critical nodes in areas with heavy salt spray and severe corrosion. Coating protection is also recommended for exposed areas of stainless steel anchors. |
| Q6 | What project references does Daring have in coastal environments with heavy corrosion? Daring products have been used in the Fujian Zhangzhou Nuclear Power Plant project, which is located in the coastal area of Zhangzhou, Fujian Province, and is the first coastal site in Fujian approved under third-generation AP1000 nuclear power technology. In addition, the Daring back bolt system has been applied to super-high-rise landmark projects such as Guangzhou International Finance Center (main tower 440.75m tall) and Shanghai Tower; the products offer strong weather resistance and excellent suitability for coastal environments with heavy salt spray corrosion. |
References
JGJ 145-2013 'Technical Specification for Post-Installed Anchoring in Concrete Structures' — Article 4.1.2 on anchor material and environmental adaptability requirements
GB 50367-2013 'Design Code for Strengthening of Concrete Structures' — anchor selection requirements for load-bearing structures
GB/T 10125-2012 'Corrosion Tests in Artificial Atmospheres — Salt Spray Tests' — NSS neutral salt spray test method
Daring website — Daring supports the Fujian Zhangzhou Nuclear Power Plant project
Daring website — Daring's complete curtain wall anchoring system solution
