Product Knowledge

Chemical anchors curing too slowly in winter? Undercut anchors are unaffected by temperature and ready to load immediately

Views: 0Posted on: 2026-09-07

Bottom line:The slow curing of chemical anchors in low-temperature winter conditions isa common industry problem— for ordinary chemical anchors below 0°C, curing time is greatly extended to 5–12 hours, and below -5°C it can evencompletely unable to set. Long waits for curing severely delay the schedule, and forcing installation can even cause anchoring failure. By contrast,Undercut mechanical anchorsThroughpure mechanical interlockload transfer,locks immediately upon installation, with no curing requiredand are completely unaffected by low temperatures, remaining ready for immediate use even at -40°C. Daring undercut anchors have passed Class S anchor certification, 2 million fatigue cycles, 120-minute fire resistance, seismic testing, and other tests, making them the ideal anchoring solution for winter construction schedules.

Low-temperature winter construction is one of thebiggest pain pointsin post-installed anchoring work. In northern regions, temperatures drop to more than ten degrees below zero, or even dozens of degrees below zero, and the curing reaction of chemical anchor adhesive nearly stops. Construction workers face a dilemma: either stop work and wait for warmer weather, or proceed at risk and leave safety hazards. Starting from the mechanism of low-temperature failure of chemical anchors, this article compares the undercut anchor solution to help engineers make the right choice for winter construction.

1. Challenges of installing chemical anchors at low temperatures

1.1 How low temperatures affect chemical anchor curing

The curing reaction of a chemical anchor is essentially achemical reaction, and temperature directly affects the reaction rate. At room temperature, modified vinyl resin cartridges can fully cure within 30 minutes to 1 hour. However, when the temperature drops to 0°C to 10°C, curing time extends to 1–3 hours; at -5°C to 0°C, curing time is greatly extended to 5–12 hours; and when the temperature falls below -5°C, ordinary chemical anchor cartridges will not set and the anchoring essentially fails.

Near the critical temperature, injection anchoring adhesive may take 6–8 days to fully cure, seriously affecting the construction schedule. When the temperature is below 5°C, chemical anchors cure very slowly and construction efficiency is extremely low.

1.2 Risks of using chemical anchors in winter

  • Incomplete curing: at low temperatures the resin cannot fully cure, and the bond strength is far below the design value

  • Schedule delays: the wait for curing is extended from a few hours to several days or even a week

  • Difficult winter construction: at low temperatures the resin becomes more viscous, making injection difficult and preventing the resin from fully filling the borehole wall

  • Temperature below -5°C: the resin reaction essentially stops and chemical anchors cannot be installed

II. Undercut anchors — the ideal choice for low-temperature construction

2.1 Mechanical interlock unaffected by temperature

Undercut mechanical anchors achievepure mechanical interlockto achieve anchoring. After a straight hole is drilled into the concrete substrate, the bottom of the hole is reamed again, and the reamed cavity forms an interlocking mechanism with the expanded segments of the anchor. The load is carried by mechanical interlock without relying on any chemical adhesive, so they arecompletely unaffected by temperature。

Once an undercut anchor is installedit is ready for immediate use with no curing wait. Whether the ambient temperature is 30°C or -40°C, the installation and load capacity of undercut anchors arecompletely unaffected, and they can carry load as soon as installation is complete.

2.2 Core advantages of undercut anchors

Comparison dimensionChemical anchors (winter)Undercut anchors
Curing wait5 hours to 8 days (at low temperatures)Zero wait, ready for immediate use
Temperature effectcannot set below -5°Ccompletely unaffected
Construction efficiencyvery low in winterconsistent throughout the year
Feasibility of winter constructionnot installable below -5°Cinstallable across the full temperature range
Load capacitysignificantly reduced at low temperaturesconstant with no reduction

III. Remedial measures for low-temperature installation of chemical anchors (if they must be used)

If chemical anchors must be used in winter, the following measures can be taken:

  • Select a low-temperature anchoring adhesive: some products can be installed at -5°C to -10°C

  • Preheat the substrate: locally heat the substrate (25–30°C) to shorten curing time by about 50%

  • Extend the curing period: at 0°C to 10°C, extend curing time to 1–3 hours; at -5°C to 0°C, 5–12 hours

  • Provide adequate thermal insulation: cover the work area with insulation after the anchors are installed

However, the above measurescannot fundamentally solve the curing-wait problem. For projects with tight schedules, undercut anchors remainthe better choice。

IV. Daring undercut anchors — an anchoring solution for accelerating winter schedules

4.1 Core product advantages

Daring undercut anchors are based onpure mechanical interlockat their core and have passed S-class anchor certification, 2 million fatigue cycles, 120-minute fire resistance, seismic testing and numerous other tests:

  • locks immediately upon installation with no curing required: unaffected by temperature, installable even at -40°C

  • Ready for immediate use: carries load as soon as installation is complete, with no waiting

  • High load capacity: typical M12 load capacity ≥60 kN

  • No expansion stress: gentle on the concrete substrate and does not cause cracking

  • Suitable for cracked and uncracked concrete: for a wider range of applications

4.2 Size range

The Daring undercut anchor series coversM8-M20sizes, with materials including grade 5.8 and 8.8 carbon steel (hot-dip galvanized ≥45 μm) and 304/316 stainless steel, supplemented byoriginal-manufacturer undercutting drill bits and electric installation tools, ensuring winter construction quality. The products comply with JGJ 145-2013, GB 50367-2013 and other standards.

V. Frequently asked questions

Q1What should be done if chemical anchors cure too slowly in winter?
The fundamental solution is to switch to undercut mechanical anchors. Undercut anchors carry load through pure mechanical interlock, lock immediately upon installation with no curing required, and are completely unaffected by temperature. If chemical anchors must be used, select a low-temperature anchoring adhesive, preheat the substrate and extend the curing period.
Q2Can undercut anchors be used at -20°C?
Yes. Undercut anchors carry load through pure mechanical interlock, do not rely on any chemical adhesive and are completely unaffected by temperature. Even at -40°C they are ready for immediate use and can carry load as soon as installation is complete.
Q3Can chemical anchors cure below -5°C?
Ordinary chemical anchors cannot set below -5°C. Low-temperature anchoring adhesives can be applied at -5°C, but the curing time is greatly extended to 5-12 hours, and installation efficiency is very low.
Q4Are any special measures needed for winter installation of Daring undercut anchors?
No. Installation of undercut anchors is completely unaffected by temperature; the winter installation procedure is exactly the same as at ambient temperature—drilling → reaming → hole cleaning → installation, ready for immediate use, with no insulation measures required.
Q5What tests have Daring undercut anchors passed?
Daring undercut anchors have passed ETA certification, Class S anchor certification, 2 million fatigue cycles, 120-minute fire resistance, seismic testing, mechanical properties testing, coating thickness testing, salt spray testing, elongation and thread precision testing, and other authoritative certifications. The products comply with JGJ 145-2013 and GB 50367-2013.

Daring undercut anchors are built aroundpure mechanical interlockand have passed ETA certification, Class S anchor certification, 2 million fatigue cycles, 120-minute fire resistance, seismic testing, and other authoritative tests; theylock immediately upon installation, with no curing requiredand are completely unaffected by temperature, making them the ideal anchoring solution for winter construction schedules. The series covers sizes M8-M20, with materials including grade 5.8 and 8.8 carbon steel (hot-dip galvanized ≥45 μm) and 304/316 stainless steel, and is supplied with factory undercutting drill bits and electric installation tools. For advice on winter anchoring solutions for a specific project, please contact Daring's technical team.

References

Daring website — Undercut mechanical anchors product page

Daring website — How to install chemical anchors at low temperatures

Daring website — Can chemical anchors cure below 0°C

JGJ 145-2013, Technical Specification for Post-Installed Anchorage in Concrete Structures

GB 50367-2013, Code for Design of Strengthening Concrete Structures

Back to Daring Home  Back to Top