Conclusion first:Mechanical anchors on hollow brick wallscannot be usedHollow bricks, aerated blocks and lightweight wall panelsare strictly prohibiteddedicated anchors. According to T/CECS 479-2017, Technical Specification for Post-Installed Anchorage of Masonry Structures, post-installed anchorage connections in hollow brick masonry should usesuch as, such asmesh-sleeve adhesive anchors and J-shaped anchors, etc. Ordinary expansion anchors create friction by expanding a metal sleeve against the hole wall, but hollow bricks contain voids and have very thin solid ribs (generally only 10-15 mm); once the sleeve expands iteasily cracking and crushing the brick ribs, or it may fall directly into a void without tightening, giving extremely poor grip. An M10 ordinary expansion anchor of the same size has a tensile capacity of about 20-25 kN in solid brick/concrete, but often <5 kN in hollow brick — the load capacitydrops sharply. If heavy objects must be fixed to a hollow brick wall, preference should be given tochemical anchors(mesh-sleeve or reverse-cone type) orthrough-wall threaded rodsolution.
In building post-installed anchorage, many construction workers habitually use expansion bolts on all kinds of walls, unaware thatusing expansion bolts on hollow brick is a waste of effort— not only is anchorage capacity seriously insufficient, but the wall may also crack, creating safety hazards. Based on code basis, structural characteristics of hollow bricks, failure mechanisms and alternatives, this article systematically answers whether mechanical anchors can be used on hollow brick walls.
I. Explicit code prohibition: expansion anchors strictly prohibited on hollow brick walls
1.1 Core code basis
According toT/CECS 479-2017, Technical Specification for Post-Installed Anchorage of Masonry Structures, this code applies to post-installed anchorage connections on masonry with sintered common bricks, sintered permeable bricks and permeable blocks, autoclaved silicate common bricks, concrete permeable bricks,sintered hollow bricks and hollow blocks, ordinary concrete small hollow blocks and autoclaved aerated concrete blocks as base materials, for fixing non-structural components and attached electromechanical equipment. However, the code explicitly states that ordinary expansion anchorsare not applicable tohollow bricks, permeable bricks and similar base materials.
JGJ 145-2013, Technical Specification for Post-Installed Anchorage of Concrete Structureslikewise clearly states that the code applies to post-installed anchorage with reinforced concrete, prestressed concrete and plain concrete as base materials,and does not apply to post-installed anchorage with masonry as the base material。
Ordinary expansion anchors are only suitable forsolid concrete and dense stone, while hollow bricks, aerated blocks and lightweight wall panelsare strictly prohibited。
1.2 Specific code provisions for anchoring on hollow brick walls
For anchoring on hollow brick walls, relevant codes make specific provisions:
Hollow block base walls (class D)should useanchors bearing load through friction and mechanical locking
Anchors used in base walls ofhollow or permeable brick masonryshouldbe J-shaped anchors
Anchors used in base walls ofhollow blocks(including ordinary concrete small hollow blocks, lightweight aggregate concrete small hollow blocks, and sintered hollow bricks and blocks)should be J-shaped anchors
II. Why ordinary expansion anchors cannot be used on hollow brick walls
2.1 Structural characteristics of hollow bricks
Hollow bricks (including sintered hollow bricks and permeable bricks) containvertical or horizontal voids, with very thin solid ribs, generally only10-15mm. This structure determines that hollow bricksdo not provide the dense base material conditions required for expansion friction anchoring。
2.2 Load-bearing principle of ordinary expansion anchors
Ordinary expansion anchors rely onexpanding a metal sleeve against the hole wall to create frictionfor anchoring. The core prerequisite is that the hole wall must be surrounded bydense solid materialable to withstand the radial expansion pressure of the sleeve. This load-bearing methodhas neither mechanical interlock nor chemical bondingand relies entirely on friction.
2.3 Why the two are 'out of place' on hollow bricks
When ordinary expansion anchors are installed on hollow bricks, the following problems occur:
Cracking brick ribs: as the sleeve expands, the thin brick ribs (10-15 mm) cannot withstand the expansion pressure,and are easily cracked or crushed
Falling into voids: if the drilled hole happens to align with a void in the hollow brick, as the sleeve expands itfalls directly into the void without tightening, and anchoring fails completely
Very poor grip: even if barely installed, the contact area between anchor and hole wall is seriously insufficient,resulting in very poor grip
2.4 Plummeting load capacity
Data comparison best illustrates the problem:
Solid brick/concrete: M10 ordinary expansion anchor has tensile capacity of about20-25kN
Permeable brick/hollow brick: anchors of the same size often have tensile capacity<5kN, withgreat scatterand inconsistent results
Load capacity drops by as much as75%-80%, and over long-term use, due to vibration, temperature differences and other factors, within weeks to months it mayloosen, and re-tightening the nut has no effect.
III. Correct anchoring solutions for hollow brick walls
3.1 Option 1: mesh-sleeve adhesive anchor (chemical anchor)
The mesh-sleeve adhesive anchor is one of therecommended solutionsfor anchoring on hollow brick walls. Its core advantages are:
Mesh sleeve retains the adhesive: the special mesh sleeve keeps the chemical adhesive inside the drilled hole,preventing it from leaking into voidsand is specifically suited to permeable/hollow bricks
does not rely on expansion pressure: the adhesive penetrates the brick voids and cures into a whole, independent of hole wall density
Suitable for various base materials: permeable bricks, hollow blocks and old walls can all be used
3.2 Option 2: special reverse-cone chemical anchor (adhesive reverse-cone anchor)
For conditions with loads >30 kg or vibration/impact (such as outdoor AC units, equipment bases), usespecial reverse-cone chemical anchors, whose principle isreverse cone + epoxy adhesive, relying onbonding + interlockdual load bearing, without relying on expansion pressure.
3.3 Option 3: J-shaped anchor
According to codes, anchors used in base walls of hollow or permeable brick masonryshould be J-shaped anchors; anchors used in hollow blocksshould be J-shaped anchors. J-shaped anchors form a mechanical lock inside the voids of hollow bricks through a special hook-like structure and are suitable for anchoring hollow brick walls.
3.4 Option 4: through-wall threaded rod + double-side plates
For heavy loads or critical locations, use athrough-wall threaded rod + double-side platesassembly, where the rod passes through the wall and is locked with plates and nuts on both ends. This solution does not rely on the anchoring force of the brick itself, but transfers the load to both sides of the wall, providing the highest safety. Where conditions allow,placing the anchor point on adjacent concrete beams or columnsis the most reliable practice.
IV. Decision guide for anchoring solutions on hollow brick walls
| Load type | Recommended anchoring solution | Description |
|---|---|---|
| <5 kg, temporary, no vibration | Heavy-duty nylon expansion plug + self-tapping screw | small pendants, display boards and other light loads |
| 5-30 kg, long-term, no vibration | Mesh-sleeve adhesive anchor(M8-M10) | wall cabinets, washbasins, pipe supports, etc. |
| >30 kg, vibration/impact | Special reverse-cone chemical anchor | outdoor AC units, equipment bases, etc. |
| Heavy loads, critical locations | Through-wall threaded rod + double-side plates | highest safety factor, independent of brick anchorage |
| All conditions | Prefer connection to concrete beams or columns | the most reliable anchoring method |
V. General principles for anchor selection in load-bearing structures
According toGB 50367-2013, Code for Design of Strengthening Concrete Structuresclause 16.1.4, in structures in seismic design zones and in members directly subjected to dynamic loads,expansion anchors must not be usedas connection elements for load-bearing structures.
Mechanical anchors for load-bearing structures should useundercut anchors with interlocking effects(self-undercutting, form-undercutting and adhesive-form-undercutting types); adhesive anchors for load-bearing structures should usespecial reverse-cone adhesive anchors。
Ordinary expansion anchors rely on the hole wall forfriction load transfer, and sustained radial expansion pressure can easily cause concrete splitting and brittle conical failure, with failurewithout warning and instant detachment, failing to meet the reliability requirements of load-bearing structures.
VI. Frequently asked questions
| Q1 | Can mechanical anchors be used on hollow brick walls? No. Ordinary expansion anchors are strictly prohibited on hollow bricks, aerated blocks and lightweight wall panels. Ordinary expansion anchors are only suitable for solid concrete and dense stone. |
| Q2 | Why don't ordinary expansion anchors work on hollow brick walls? Hollow bricks contain voids and have thin solid ribs (10-15 mm). Expansion anchors create friction by expanding a sleeve against the hole wall; expansion easily cracks and crushes the brick ribs, or the anchor falls into a void without tightening, reducing capacity from 20-25 kN to <5 kN. |
| Q3 | What anchors are suitable for hollow brick walls? Mesh-sleeve adhesive anchors, J-shaped anchors or special reverse-cone chemical anchors are recommended. For larger loads, use a through-wall threaded rod with double-side plates, or preferably place the anchor point on adjacent concrete beams or columns. |
| Q4 | What do codes require for anchors on hollow brick walls? T/CECS 479-2017, Technical Specification for Post-Installed Anchorage of Masonry Structures, applies to post-installed anchorage connections in hollow brick masonry. Hollow block base walls should use anchors that bear load through friction and mechanical locking, and anchors used in hollow blocks should be J-shaped. |
| Q5 | Does Daring offer anchoring products for hollow brick walls? The Daring chemical anchor range includes special reverse-cone chemical anchors, paired with Daring DL-200E modified epoxy injection anchoring adhesive, suitable for anchoring in permeable bricks, hollow blocks and similar base materials. For specific hollow brick wall anchoring solutions, please consult the Daring technical team. |
The Daring chemical anchor range covers high-strength, capsule, special reverse-cone and dynamic-load reverse-cone anchors, paired with Daring's national grade A DL-200E modified epoxy injection anchoring adhesive, available in grade 5.8 or higher carbon steel or 304/316 stainless steel. Special reverse-cone chemical anchors offer strong bond anchorage, temperature and seismic resistance, and suit a variety of base materials. For hollow brick wall anchoring selection advice for specific projects, please consult the Daring technical team.
References
T/CECS 479-2017, Technical Specification for Post-Installed Anchorage of Masonry Structures
JGJ 145-2013, Technical Specification for Post-Installed Anchorage of Concrete Structures
GB 50367-2013, Code for Design of Strengthening Concrete Structures
JG/T 366-2012, Anchors for External Wall Insulation
