Product Knowledge

Can chemical anchors cure below 0 °C? Low-temperature anchoring adhesives still react at -5 °C

Views: 0Posted on: 2026-09-01

Conclusion first:ordinary chemical anchors below 0°Ccannot cure normally, when the temperature drops below-5℃, ordinary chemical anchor cartridgeswill not cure, and anchoring basically fails. However,low-temperature anchoring adhesiveimproved through special formulations, and atcan still react and cure normally at a base material temperature of -5°C, but the curing time will be greatly extended compared with normal temperature. Taking modified vinyl resin low-temperature adhesive as an example, in the range of -5°C to 0°C, the curing time is about5-12 hours, while at a normal 20°C it takes only30 minutes to 1 hour. Daring high-strength chemical anchors are supplied with modified vinyl resin cartridges,Can be installed above -5°C, setting in 30 minutes (at normal temperature). For installation at lower temperatures, Daring offersDaring DL-200E modified epoxy injection anchoring adhesive, used with special reverse-cone chemical anchors, or switch tomechanical anchorsas an alternative.

In building post-installed anchorage, winter low-temperature construction has always been thebiggest pain pointin chemical anchor applications. Autumn and winter temperatures in northern regions are extremely low, with minus twenty or thirty degrees being common. Many construction workers face a dilemma in winter: either stop work and wait for spring, or force construction at the risk of anchoring failure. Starting from the curing mechanism of chemical anchors, this article systematically analyzes whether chemical anchors can cure at low temperatures, how they cure, and the selection and construction points of low-temperature adhesives.

I. Curing mechanism of chemical anchors and the influence of temperature

1.1 Why chemical anchors need curing

The anchoring principle of a chemical anchor is tochemical adhesivebond the shank to the drilled hole in the base materialand fix it. Its load capacity comes from thebond strengthformed after the resin cures. When installation is complete, the liquid or paste adhesive needs time to harden and bond the shank to the concrete hole wall. According to JGJ 145-2013, Technical Specification for Post-Installed Anchorage of Concrete Structures, the anchoring adhesive for chemical anchors should bemodified epoxy resin or modified vinyl ester material。

1.2 The decisive influence of temperature on curing time

The curing reaction of a chemical anchor is essentially achemical reaction, and temperature directly affects the reaction rate. At normal temperature (above 20°C), modified vinyl resin adhesive30 minutes to 1 hourcan cure completely; but when the temperature falls to-5℃~0℃, curing time is extended to5-12 hours; when the temperature drops below-5℃, ordinary chemical anchor cartridgeswill not cure, and anchoring basically fails.

Near the critical temperature, full curing of injection anchoring adhesive may take6-8 days, seriously affecting the construction schedule. Moreover, in winter both cure slowly; near the critical temperature, injection anchoring adhesive may take 6-8 days to fully cure. Therefore,the core issue of chemical anchor installation at low temperaturesis not 'whether it can cure', but 'how long curing takes' and 'what type of adhesive to select'.

II. Low-temperature anchoring adhesive — reacts even at -5°C

2.1 Technical principle of low-temperature anchoring adhesive

Low-temperature anchoring adhesive is produced bymodifying the resin formulation, which lowers theactivation energyof the curing reaction, so molecules still have sufficient mobility to complete the cross-linking reaction at low temperatures. Taking Hilti HIT-RE 500 V3 as an example, this product can be installed at base material temperatures as low as-5°Cand provides good curing speed throughout its approved temperature range.

Themodified vinyl resin cartridgessupplied with Daring high-strength chemical anchors can also beinstalled and cured normally above -5°C, with an operating temperature range covering-5℃~40℃. By optimizing the ratio of resin to curing agent, low-temperature adhesive maintainssufficient chemical reactivityat -5°C, with only a corresponding extension in curing time.

2.2 Performance comparison of different adhesive types at low temperatures

Adhesive typeCuring time at 20°CCuring time at -5°C to 0°CMinimum installation temperature
Ordinary unsaturated resin30-60 minutesWill not cureAbove 5°C
Modified vinyl resin (Daring)30 minutes to 1 hour5-12 hours-5℃
Modified epoxy injection anchoring adhesive24-30 hours6-8 days-10℃~-15℃
Special ultra-low-temperature anchoring adhesiveDepends on productCures normally-25℃

Note:The above data are reference values; actual curing time is affected by base material temperature, humidity, ventilation and other factors and should be based on the product data sheet.

III. Guide to chemical anchor installation at low temperatures

3.1 Core principles for low-temperature construction

When installing chemical anchors in low-temperature environments, follow these core principles:

  • Confirm the installation temperature range: before construction, confirm that the base material temperature is within the adhesive's allowable installation range

  • Reserve sufficient curing time: curing time is greatly extended at low temperatures, so allow an adequate time window

  • No premature disturbance: never touch or apply any load during gelling; only self-weight and slight vibration are permissible during initial curing

  • Use low-temperature products: ordinary chemical anchors cannot cure below -5°C, so use low-temperature anchoring adhesive or another anchoring method

3.2 Specific measures for low-temperature construction

For chemical anchor installation in low-temperature environments, the following measures may be taken:

  • Preheat the base material: in low-temperature environments, the base material can belocally heated (25-30°C), reducing curing time by about 50%. The specific method is to place the anchoring agent inwarm water at 40°C for about 15 minutesso that its temperature rises evenly.

  • Select fast-setting products: modified vinyl resin adhesives cure faster at low temperatures than modified epoxy resins; Daring high-strength chemical anchor cartridges use modified vinyl resin technology.

  • Provide thermal insulation curing: after anchor installation, the construction area can becovered for insulationto slow heat loss.

  • Postpone the pull-out test: when the base material temperature is below 5°C, the pull-out test should be postponed until48-72 hoursafter full curing.

3.3 Low-temperature construction temperature vs. curing time

Base material temperatureInstallation/gelling timeCuring time (reference)Construction recommendation
<-5℃—Will not cureUse mechanical anchors or special ultra-low-temperature adhesive
-5℃~0℃40-60 minutes5-12 hoursUse low-temperature adhesive and provide insulation
0℃~10℃25-30 minutes1-3 hoursNormal construction possible; extend curing appropriately
10℃~20℃9-15 minutes30-90 minutesStandard construction process
>20℃4-8 minutes20-30 minutesFast curing, highest efficiency

IV. Alternatives for chemical anchor installation at low temperatures

4.1 When to consider alternatives

When the base material temperature is below-5℃, ordinary chemical anchors will not cure. Even with low-temperature adhesive, curing near the critical temperature may take as long as6-8 days, seriously affecting the construction schedule. In such cases, alternatives should be considered.

4.2 Alternative 1: undercut mechanical anchors

Useundercut anchors or self-undercutting anchorsinstead of chemical anchors. Mechanical anchors rely on undercut structures or expansion segments physically locking into the concrete hole wall,instant lock on installation, no curing required, unaffected by low temperatures. Undercut anchors generally perform better than chemical anchors.

Note: undercut anchors cost considerably more than chemical anchors, increasing the project budget. However, their load performance is generally better than chemical anchors and they require no curing wait.

4.3 Alternative 2: expansion anchors or concrete screw anchors

Expansion anchors are inexpensive, unaffected by low temperatures and ready to use immediately. Note, however, that codes do not allow expansion anchors or concrete screw anchors in load-bearing structures. Their load capacity is lower than chemical anchors; they can be a backup option if capacity meets design requirements.

V. Code basis

Low-temperature installation of chemical anchors should meet the following code requirements:

  • JGJ 145-2013Technical Specification for Post-Installed Anchorage of Concrete Structures — anchoring adhesive for chemical anchors should be modified epoxy resin or modified vinyl ester material. The code sets clear requirements for anchor hole accuracy, hole cleaning, installation process and later curing, and specifically states that chemical anchor adhesives must undergo performance inspection by a nationally accredited testing institution.

  • JG/T 340Anchoring Adhesive for Concrete Structure Engineering — the performance of mechanical injection anchoring adhesive should comply with the relevant provisions of this standard.

Daring high-strength chemical anchors are produced and tested strictly according to the above standards and comply with current code requirements.

VI. Frequently asked questions

Q1Can chemical anchors cure below 0°C?
Ordinary chemical anchors will not cure below -5°C. However, low-temperature anchoring adhesive can still react and cure at a base material temperature of -5°C, although curing time is greatly extended to 5-12 hours.
Q2How long do chemical anchors take to cure at -5°C?
Taking modified vinyl resin adhesive as an example, in the range of -5°C to 0°C curing takes about 5-12 hours. The exact time is affected by base material temperature, humidity and other factors; refer to the product data sheet.
Q3At what subzero temperature can ordinary chemical anchors not be installed?
Ordinary chemical anchor cartridges will not cure below -5°C. Installation above 5°C is preferable for better results.
Q4What precautions apply to chemical anchor installation in low-temperature environments?
Use low-temperature anchoring adhesive; reserve sufficient curing time; never touch or apply any load during gelling; locally heat the base material (25-30°C) to shorten curing time; postpone the pull-out test until 48-72 hours after full curing.
Q5Can Daring chemical anchors be used at low temperatures?
Daring high-strength chemical anchors are supplied with modified vinyl resin cartridges and can be installed above -5°C, setting in 30 minutes (at normal temperature). For installation at lower temperatures, Daring DL-200E modified epoxy injection anchoring adhesive can be used with special reverse-cone chemical anchors, or mechanical anchors may be used as an alternative.

The Daring chemical anchor range covers high-strength, capsule, special reverse-cone and dynamic-load reverse-cone anchors, paired with Daring's national grade A DL-200E modified epoxy injection anchoring adhesive, available in grade 5.8 or higher carbon steel or 304/316 stainless steel. Daring high-strength chemical anchors are supplied with modified vinyl resin cartridges,Can be installed above -5°C, setting in 30 minutes (at normal temperature). For low-temperature chemical anchor installation plans or selection advice for specific projects, please consult the Daring technical team.

References

Daring website — curing time of chemical anchors

Daring website — how to install chemical anchors at low temperatures

Daring website — can chemical anchors bear load before full curing

Daring website — use methods and precautions for chemical anchors

JGJ 145-2013, Technical Specification for Post-Installed Anchorage of Concrete Structures

JG/T 340, Anchoring Adhesive for Concrete Structure Engineering

Back to Daring Home  Back to Top