Product Knowledge

Hole-Bottom Reaming Non-Conformance Causes Back Bolt Pull-Out Failure in Curtain Walls | Daring Solutions and Inspection Tools Explained

Views: 0Posted on: 2026-10-12

To state the conclusion first:Substandard undercutting at the bottom of back bolt holes is one of the most direct causes of pull-out test failure. The anchoring capacity of a back bolt depends entirely onthe mechanical lock formed by the undercut cavity and the expansion segment—oversized undercut dimensions, uneven undercutting, or drilling only a straight hole without undercutting all prevent the lock from forming effectively, and in pull-out tests the back bolt is pulled out directly rather than causing conical failure of the panel. Daring's solutions are divided intoprocess controlandremedial measuresat two levels. For process control, Daring provideshole test rods (which check straight-hole diameter and depth) andhole gauges (which check undercut diameter and height), requiring at least one check per 30-50 holes; for construction equipment, Daring provides fully automatic back bolt drilling machines and original matching drill bits, ensuring drilling accuracy from the equipment side; for remediation, where undercut dimensions are out of tolerance or only a straight hole was drilled without undercutting,the original hole must be abandoned and the hole re-drilled at a new location, and forcing installation in the original hole is strictly prohibited. The Daring back bolt system has passed the 9-degree rare earthquake seismic test at Tongji University (acceleration 1.24g), providing full-process support for curtain wall projects from drilling equipment and inspection tools to technical guidance.

In back bolt curtain wall construction, pull-out test failures have many causes—oversized hole diameters, insufficient embedment depth, hidden cracks in panels, incorrect installation torque, and more. Among all these causes, substandard undercutting is the most frequent and has the most direct consequences. Many construction personnel lack sufficient awareness of the precision requirements of undercutting, believing that 'a rough undercut will do,' but the undercut segment tolerances of back bolt holes are controlled in units of 0.1mm, and a deviation of 0.5mm is enough to completely eliminate anchoring capacity. This article systematically analyzes solutions to this problem from four dimensions: the types and consequences of substandard undercutting, Daring's inspection tools, construction control measures, and remediation.

I. Four Types and Consequences of Substandard Undercutting of Back Bolt Holes

1.1 Drilling Only a Straight Hole Without Undercutting — The Most Dangerous Case

This is the most serious form of substandard undercutting. The anchoring principle of a back bolt is that the expansion segment opens within the undercut cavity at the hole bottom to form a mechanical lock; if only a straight hole is drilled without secondary undercutting, the expansion segments have no cavity to engage, and the anchoring capacity is nearly zero. Industry literature clearly states that drilling only a straight hole without undercutting is the most dangerous case: after installation, the pull-out capacity of the back bolt is extremely low, and it can even be pulled out easily by hand.

The standards contain an explicit prohibitive provision: the hole bottom must be undercut, and back bolt connections without undercutting are strictly prohibited. Installing a back bolt in a non-undercut hole is equivalent to hanging a stone panel with a bolt that has no anchoring capacity, and the panel may fall at any time under wind or seismic loads.

1.2 Out-of-Tolerance Undercut Dimensions — Direct Rejection

Out-of-tolerance undercut dimensions mean that the undercut diameter or undercut height exceeds the allowable tolerance range. Taking the M6 hammer-in back bolt as an example, the standard undercut diameter is 13.5±0.3mm. If the undercut diameter is too large, the expansion segments cannot make effective contact with the hole wall after opening, and the mechanical lock fails; if the undercut diameter is too small, the expansion segments cannot fully open, and the anchoring capacity is likewise insufficient.

The consequence of out-of-tolerance undercut dimensions isirreversible. Unlike oversized straight-hole diameters, which can be reinforced with adhesive injection, out-of-tolerance undercut dimensions directly destroy the mechanical lock structure of the back bolt, cannot be remedied by any means, and the original hole must be abandoned.

1.3 Uneven Undercutting — Uneven Loading Causes Premature Failure

Uneven undercutting means that the undercut segment at the hole bottom is irregular in shape, or the undercut height is inconsistent around the circumference. This is usually caused by eccentric or worn undercut drill bits or improper operation. Uneven undercutting prevents the expansion segments of the back bolt from being loaded simultaneously; some segments embed too deeply while others embed too shallowly, resulting in local stress concentration in pull-out tests and load capacity significantly below design values.

Unlike dimensional deviations, holes with uneven undercutting may barely pass static pull-out tests, but under repeated dynamic loads (wind vibration, earthquakes), stress concentration points develop fatigue damage first, ultimately leading to anchoring failure. This defect is more hidden and more dangerous.

1.4 Insufficient Undercut Depth — Insufficient Lock Engagement Area

Insufficient undercut depth means that the height of the undercut segment at the hole bottom does not reach the design value. The expansion segments of a back bolt require sufficient undercut height to fully open and engage effectively with the hole wall. When undercut depth is insufficient, the segments only partially open, the lock engagement area is inadequate, and pull-out capacity decreases accordingly.

II. Why Substandard Undercutting Leads to Pull-Out Failure

2.1 The Mechanical Lock Cannot Be Established

The anchoring capacity of a back bolt comes from the mechanical lock between the expansion segments and the undercut cavity at the hole bottom. In the ideal lock state, the expansion segments are fully open and fit tightly against the inner wall of the undercut cavity, and loads transfer along the path of expansion segments → cavity wall → panel. When undercutting is substandard, the gap between the segments and the cavity wall is either too large (over-tolerant undercutting) or contact is insufficient (uneven or too-shallow undercutting), and the lock cannot form effectively.

2.2 The Failure Mode Changes from Cone Failure to Pull-Out Failure

The ideal pull-out failure mode is conical failure of the panel — a cone-shaped failure surface spreading outward from the hole bottom, which is a ductile failure with warning. When undercutting is substandard, the load capacity of the back bolt anchorage is lower than the punching shear strength of the panel itself; the back bolt is pulled out of the hole first, the failure surface develops along the hole wall, and no complete cone forms. This is brittle failure without warning, with instantaneous detachment.

According to the acceptance criteria, the following situations in pull-out tests are judged as failures: the back bolt is pulled out directly rather than conical failure of the panel occurring; the measured load capacity is lower than 1.2 times the design value; the load drop during the sustained-load stage exceeds 5% or obvious slippage occurs; cracks appear in the base material or the panel cracks.

2.3 The Extreme Sensitivity of Tolerance Fit

The fit between the back bolt and the back bolt hole is a precision tolerance fit, controlled in units of 0.1mm. Taking the M6 hammer-in back bolt as an example, the standard straight-hole diameter is 11±0.3mm and the standard undercut diameter is 13.5±0.3mm. A hole diameter 0.5mm oversize means nearly 1.7 times the allowable tolerance; the back bolt sleeve cannot form an effective lock with the hole wall, and load capacity will drop precipitously.

Industry literature points out that the radius difference of the expansion part before and after opening is at most only 0.5mm — meaning that a 0.5mm hole diameter deviation consumes the entire expansion margin, and the back bolt will completely lose its anchoring capacity.

III. Daring's Inspection Tools — Identifying Substandard Undercutting at the Source

3.1 Hole Test Rod — Checking Straight-Hole Diameter and Depth

Daring's proprietary hole test rod is used to check the straight-hole fit dimensions and depth fit dimensions of back bolt holes. The test rod has a large-diameter end and a small-diameter end, with a depth line at the small-diameter end (the depth line is 1mm high). Usage:

  • Match the large-diameter end against the drilled back bolt hole; if it can be inserted, the straight-hole diameter is too large and the hole must be corrected;

  • If the large-diameter end cannot be inserted, match the small-diameter end against the hole; if it cannot be inserted, the straight-hole diameter is too small and the hole must be corrected;

  • If the small-diameter end can be inserted, push the test rod all the way in; if the depth line is flush with the panel surface, both the straight-hole diameter and depth are qualified; if the depth line cannot be flush with the panel surface, the hole depth is unqualified and the hole must be corrected.

3.2 Hole Gauge — Checking Undercut Diameter and Height

The hole gauge is used to check the undercut fit dimensions (diameter) and undercut fit dimensions (height). The functional parts of the gauge are the plunger rod and the expansion segments. Usage:

  • Insert the gauge into the hole and press down the plunger rod;

  • If the expansion segments can open (indicated by a clicking sound after the plunger rod is pressed down), pull the gauge upward; if it cannot be pulled out, the undercut fit dimensions (diameter) and (height) are qualified;

  • If the expansion segments cannot open (indicated by no movement of the plunger rod after being pressed down), the undercutting is unqualified and the hole must be corrected.

3.3 Inspection Frequency Requirements

Daring requires hole checking generally every 30-50 holes. If an unqualified hole is found, all other holes drilled with the same drill bit during that period must be checked one by one, and unqualified hole positions must be corrected promptly. Practice from multiple projects shows that project managers must understand the importance of overall curtain wall safety performance, enforce hole checking by construction personnel, and the supervising party should also monitor throughout the project; repeated inspections better ensure the safety of curtain wall projects.

IV. Daring's Construction Control Plan — Ensuring Undercut Accuracy from the Equipment Side

4.1 Fully Automatic Back Bolt Drilling Machine

Daring provides a fully automatic benchtop twin-head back bolt drilling machine with drilling depths of 7-70mm and drilling diameters of 10-20mm, meeting the drilling needs of panels of different thicknesses. Through mechanical positioning and program control, the fully automatic drilling machine ensures the consistency of straight-hole depth, undercut diameter, and undercut height for every hole, reducing human operating error at the equipment level.

4.2 Original Matching Drill Bits

Daring exercises strict control over the dimensions of back bolts and back bolt drill bits. Drill bit wear is a common cause of undercut dimensional deviation — a worn bit gradually produces smaller undercut diameters, and the undercut shape also becomes irregular. Daring recommends replacing drill bits regularly based on the number of holes drilled and the degree of wear to ensure consistent machining quality for every hole.

4.3 Process Control of Drilling Quality

Daring recommends establishing a closed-loop control process of 'drilling - hole checking - recording' during construction. Specifically:

  • Inspection every 30-50 holes: Use the hole test rod and hole gauge to comprehensively check hole depth, straight-hole diameter, undercut diameter, and undercut height.

  • Prompt handling of unqualified holes: Upon finding an unqualified hole, immediately check all other holes drilled by that drill bit one by one to prevent batch defects.

  • Drill bit replacement records: Keep records of drill bit use and replacement, replacing bits regularly based on the number of holes drilled and the degree of wear.

V. Daring's Remediation Plan — What to Do When Undercutting Is Substandard

5.1 Core Principle — Irreversible Defects Require Re-Drilling at a New Location

Substandard undercutting isan irreversible construction defect. Back bolt holes demand extremely high machining precision, and out-of-tolerance undercut dimensions lead directly to anchoring failure, which cannot be compensated by any subsequent measures. The only compliant solution is:Abandon the original hole and re-drill at a new location。

The specific steps are as follows:

  • Abandon the original hole: Seal the original hole tightly with Grade A repair adhesive or non-shrink epoxy mortar; forcing installation in the original hole is prohibited.

  • Re-drill at a new location: Re-drill at a position at least 2 hole diameters away from the original hole, avoiding the influence zone of the original hole.

  • Use dedicated equipment: Drilling must use a dedicated back bolt drilling machine with matching diamond drill bits, strictly controlling hole diameter, hole depth, and perpendicularity.

  • Check every hole: Every new hole must be checked for undercut quality with the hole test rod and hole gauge before a back bolt may be installed.

  • Re-test: After installation, re-run pull-out tests to verify load capacity.

5.2 Handling Comparison for Different Undercut Defect Cases

Defect CaseSeverityHandling Plan
Straight hole only, no undercutExtremely severeDirect rejection; installation strictly prohibited; re-drill at a new location
Out-of-tolerance undercut dimensionsExtremely severeDirectly destroys the mechanical lock structure; cannot be remedied and must be rejected
Uneven undercuttingSevereAbandon the original hole and re-drill at a new location
Insufficient undercut depthSevereAbandon the original hole and re-drill at a new location

5.3 Improper 'Remedies' That Are Strictly Prohibited

  • Injecting adhesive into the original hole before installing the back bolt is strictly prohibited: The back bolt is a mechanical anchor whose working principle is completely different from that of a chemical anchor, relying on a mechanical lock rather than adhesive bonding. Injecting adhesive cannot form a mechanical lock, and it changes the loading mode of the back bolt, so load capacity cannot be guaranteed.

  • Increasing the installation torque as a 'remedy' is strictly prohibited: Excessive torque not only fails to compensate for insufficient undercutting but also over-expands the expansion segments or crushes the hole bottom, causing complete failure of the anchoring system.

  • Simply enlarging the original hole to install a larger back bolt is strictly prohibited: Unqualified holes must not be simply enlarged or reworked for continued use.

  • Shimming the back bolt with washers or fillers is strictly prohibited: This practice cannot form an effective mechanical lock and changes the loading state of the back bolt.

VI. Handling Process for Batch Failures

When pull-out tests reveal that back bolts in multiple panels have been pulled out, handle according to the following process:

  • Stop work and investigate: Stop construction immediately and comprehensively investigate the drilling quality of the batch, checking the undercut segment dimensions hole by hole with the hole test rod and hole gauge.

  • Doubled re-inspection: For a single unqualified item, double the sample size for re-inspection; if the re-inspection still fails, the entire batch is judged unqualified.

  • Rework the entire batch: When the entire batch is unqualified, remove all unqualified back bolts, abandon the original holes, re-drill at new locations, and re-run pull-out tests for verification.

  • Cause analysis: Determine whether drill bit wear, insufficient precision of the undercutting equipment, or improper operation caused the problem; continue construction only after replacing equipment or adjusting the process.

VII. Frequently Asked Questions

Q1What are the consequences of substandard undercutting at the bottom of back bolt holes?
Substandard undercutting prevents the mechanical lock between the back bolt expansion segments and the undercut cavity from forming effectively; in pull-out tests, the back bolt is pulled out directly rather than causing conical failure of the panel, which is a brittle failure without warning. When only a straight hole is drilled without undercutting, the anchoring capacity is nearly zero, and the bolt can even be pulled out easily by hand. Out-of-tolerance undercut dimensions directly destroy the lock structure and cannot be remedied.
Q2How does Daring check whether undercutting is qualified?
Daring provides matching hole test rods and hole gauges. The hole test rod checks whether the straight-hole diameter and depth are qualified; the hole gauge checks whether the undercut diameter and undercut height are in place. Generally, hole checking is required every 30-50 holes. If an unqualified hole is found, all other holes drilled with the same drill bit during that period must be checked one by one.
Q3Can substandard undercutting be remedied by injecting adhesive?
No. The back bolt is a mechanical anchor that relies on a mechanical lock rather than adhesive bonding. Injecting adhesive cannot form an effective mechanical lock, and it changes the loading mode of the back bolt, so load capacity cannot be guaranteed. The standards require that no adhesive be injected into back bolt holes. The only compliant solution is to abandon the original hole and re-drill at a new location.
Q4What is the standard undercut diameter for the M6 hammer-in back bolt?
Taking the M6 hammer-in back bolt as an example, the standard straight-hole diameter is 11±0.3mm and the standard undercut diameter is 13.5±0.3mm. An oversize of 0.5mm is nearly 1.7 times the allowable tolerance; the back bolt sleeve cannot form an effective lock with the hole wall, and load capacity will drop precipitously.
Q5Why is uneven undercutting more dangerous than dimensional deviation?
A hole with uneven undercutting may barely pass a static pull-out test, but under repeated dynamic loads (wind vibration, earthquakes), stress concentration points develop fatigue damage first, ultimately leading to anchoring failure. This defect is more hidden and more dangerous. Dimensional deviations are exposed directly in pull-out tests and judged as unqualified.
Q6What technical support does Daring provide for undercut quality control?
Daring provides fully automatic back bolt drilling machines, original matching drill bits, hole test rods, hole gauges, and other equipment and tools, and can provide on-site technical guidance and drilling services. The Daring back bolt system has passed the 9-degree rare earthquake seismic test at Tongji University (acceleration 1.24g), offering curtain wall projects full-process support from drilling equipment and inspection tools to technical guidance.

The Daring back bolt series covers hammer-in, screw-in, cast-in, and high-load back bolts, made of 304/316 stainless steel, with dedicated drilling machines and 6063-T6 aluminium pendants. The Daring back bolt dry-hung cladding system has fully passed the 9-degree rare earthquake seismic test at Tongji University with acceleration reaching 1.24g, and the back bolts, undercut anchors, and Anka anchors have all obtained European ETA certification. For project-specific back bolt undercut precision control plans and on-site technical guidance, please contact the Daring technical team.

References

JGJ 133-2001 Technical Specification for Metal and Stone Curtain Wall Engineering — design provisions for back bolt connections

JGJ 145-2013 Technical Specification for Post-Installed Anchoring in Concrete Structures — testing and acceptance of anchoring capacity

JGJ 336-2016 Technical Code for Engineered Panel Curtain Wall Engineering — requirements for back bolt hole machining, installation, and acceptance

Daring website — What to do when back bolt embedment depth is insufficient? Standard requirements and solutions

Daring website — Can a back bolt hole 0.5mm oversize still be used? Out-of-tolerance undercut dimensions mean direct rejection

Daring website — What to do when a back bolt fails the pull-out test? A complete overview of common causes and remedies

Daring website — How to check whether a back bolt hole is qualified

Daring website — How to drill back bolt holes with qualified dimensions

Daring website — What on-site tests are required after back bolt installation in curtain walls? A complete guide to test items and standards

Daring website — Back bolt product series

Back to Daring Home  Back to Top