Product Knowledge

Why are undercut anchors safer than chemical and expansion anchors? The five core advantages explained

Views: 0Posted on: 2026-09-07

First, the conclusion:Undercut anchors are safer than both chemical anchors and expansion anchors, which is determined by theirload transfer principle. Undercut anchors usepure mechanical interlock load transfer, relying on neither friction nor chemical bonding, and perform best undercracked concrete, seismic zones, and dynamic loads—three demanding service conditions. By comparison: expansion anchors rely on friction (prone to loosening under vibration), chemical anchors rely on adhesive bonding (long-term durability is questionable and performance drops at high temperature), while undercut anchors rely onthe rigid interlock formed by reaming at the base of the hole, with a load-bearing capacity reaching2–3 times, and the failure mode isanchor pull fracturerather than being pulled out, and featuresafety warning. Daring undercut anchors have passedClass S anchor certification, 2-million-cycle fatigue resistance, 120-minute fire resistance and seismic testingamong other tests, making them a compliant choice for anchoring in load-bearing structures.

In post-installed anchoring work, anchor safety has always been the primary concern of designers and construction personnel. Expansion anchors, chemical anchors, and undercut anchors are three mainstream anchoring products, but their safety levels differ substantially. This article explains why undercut anchors are safer from the perspectives of load transfer principle, seismic performance, durability, installation reliability, and failure mode.

1. Comparison of load transfer principles of the three anchor types

1.1 Expansion anchors — friction-based load transfer

Expansion anchors rely on the expansion element of the anchor developingfrictionagainst the hole wall for anchorage. When the nut is tightened, the expansion body (sleeve or expansion segments) is pressed firmly against the hole wall, generating pull-out resistance through the coefficient of friction between the concrete and the metal.

Safety hazards: Once the substrate cracks or is subjected to vibration, the friction force candecrease significantly, and the anchor may slip or even pull out. The ultimate load capacity of expansion anchors decreases to varying degrees under dynamic loads. Codes explicitly stipulate that expansion anchorsare strictly prohibited in load-bearing structures。

1.2 Chemical anchors — chemical bonding

Chemical anchors usechemical adhesiveto bond the threaded rod into the drilled hole in the substrate. Their load capacity comes from thebond strength。

Safety hazards: The adhesive carriesan aging risk; its long-term stability is inferior to that of mechanical anchors; in high-temperature environments (such as a fire) adhesive performance deteriorates sharply; in humid environments bond strength is substantially reduced; and strict curing before loading is required. Ordinary chemical anchorsare strictly prohibited in cracked concrete and load-bearing structures。

1.3 Undercut anchors — mechanical interlock

After a straight hole is drilled in the concrete substrate, an undercut anchor reams the holeagain at its base, and the reamed cavity and the anchor's expanded key segments form aninterlocking mechanism. Its load transfer mode ismechanical interlock load transfer, without relying on friction; the anchoring principle is similar to the stress distribution of cast-in foundation bolts.

Safety advantages: The interlocking structuredoes not rely on friction, so stable anchoring force is maintained even if the substrate cracks; there is no expansion stress, making it gentle on the substrate; and load capacity can reach the ultimate strength of the anchor material (anchor tensile rupture). Undercut anchors are themandatory requirement for load-bearing structurestype of anchor.

2. Comprehensive comparison of the safety of the three anchor types

Comparison dimensionExpansion anchorChemical anchorUndercut anchor
Load transfer principleFriction-basedChemical bondingMechanical interlock
Failure tensile load, M12Approx. 20 kN (anchor pull-out)Approx. 43.8 kN (grade 5.8) or ≥67.4 kN (grade 8.8, threaded rod rupture)Approx. 43.8 kN (grade 5.8) or ≥67.4 kN (grade 8.8)
Suitable for cracked concrete❌ Not applicable❌ Not applicable for standard type✅ Applicable
Seismic performanceReduced load capacity under dynamic loadsAffected by the adhesiveExcellent
Fire resistance✅ Good❌ Adhesive fails at high temperature✅ 120-minute fire resistance
Fatigue performanceProne to fatigue looseningAdhesive fatigue performance is mediocrePasses 2 million cycles
Failure modeAnchor pull-out (no warning)Adhesive debonding (no warning)Anchor tensile rupture (with warning)
Suitable for load-bearing structures❌ Strictly prohibited❌ Strictly prohibited for standard type✅ Mandatory requirement
Load-bearing after installationImmediate load-bearingCuring time requiredImmediate load-bearing

3. Five core safety advantages of undercut anchors

Advantage 1: Pure mechanical interlock, with no reliance on friction or adhesive

Undercut anchors form arigid mechanical interlockby reaming at the base of the hole; load capacity depends on neither the coefficient of friction nor adhesive aging. This interlocking structure ensures stable anchoring force underbase material cracking, long-term vibration and temperature changesunder complex working conditions, the anchoring force remains stable. Figuratively speaking, expansion anchors 'wedge' in place, chemical anchors 'bond' in place, and undercut anchors 'lock' in place.

Advantage 2: two to three times the load-bearing capacity, with a failure mode of 'anchor pull fracture'

Under the same size, same base material and same embedment depth, the effective load-bearing capacity of undercut anchors can reachtwo to three timesthat of ordinary expansion anchors. Taking the M12 as an example, the ultimate pull-out force of an expansion anchor is about 30 kN (anchor pulled out), while that of an undercut anchor can reachover 60 kN(anchor pull fracture). By comparison, the minimum tensile load of a grade 5.8 M12 chemical anchor is43.8kNand that of a grade 8.8 chemical anchor can reach67.4kN. The load on an undercut anchor generally reaches the ultimate strength of the anchor material, with a failure mode ofanchor pull fracture— in engineering this failure mode isductile failure, with obvious deformation as a warning before failure, whereas anchor pull-out isbrittle failurewith no warning and instantaneous detachment.

Advantage 3: No expansion stress, gentle on the base material

Undercut anchorshave no expansion stress, so the anchoring process generates almost no internal stress in the concrete base material. Expansion anchors exert continuous radial expansion pressure on the borehole wall during installation, which readily causes the base material tosplit and spall at the edges, especially when the edge distance is insufficient. Undercut anchors lock through reaming at the bottom of the hole, concentrating the load in the dense, deep concrete at the hole bottom; they have almost no effect on the member edge and are particularly suitable formembers with small edge distances or narrow edgesanchoring.

Advantage 4: Seismic and fatigue resistance, verified over 2 million cycles

Under dynamic loads, undercut anchorsare essentially unaffected in load-bearing capacity, and do not slip under fatigue loads or vibration. Daring undercut anchors have passedthe 2-million-cycle fatigue resistance testandthe seismic test of the National Building Materials Testing Center, and deliver stable and excellent anchoring performance under vibration loads, impact loads and earthquakes. The load-bearing capacity of expansion anchors decreases significantly under dynamic loads, and the adhesive of chemical anchors may also suffer fatigue damage under long-term vibration.

Advantage 5: Mandated by specifications, the first choice for load-bearing structures

According toGB 50367-2013, 'Code for Design of Strengthening Concrete Structure', Clause 16.1.3, mechanical anchors used in load-bearing structures should beundercut anchors with a locking effect. When anchors are used in load-bearing structures in seismic fortification zones, undercut anchors or special reverse-cone adhesive anchors should be used. Ordinary expansion anchors and chemical anchorsare strictly prohibited in load-bearing structures. Undercut anchors arethe only mechanical anchors mandated by the specifications for use in load-bearing structures。

IV. Selection Decisions for Undercut Anchors and Other Anchors

Core selection principle

Working conditionRecommended anchorStrictly prohibited
Load-bearing structuresUndercut anchorExpansion anchors, ordinary chemical anchors
Cracked concreteUndercut anchor, reverse-cone chemical anchorExpansion anchor
Seismic fortification zonesUndercut anchorExpansion anchor
Dynamic loads and vibrating environmentsUndercut anchorExpansion anchor (prone to loosening)
Members with small edge distances/narrow edgesUndercut anchorExpansion anchor (risk of edge spalling)
Non-load-bearing, dry indoor environmentsExpansion anchor / chemical anchor— (cost priority)

Key tips

  • Load-bearing structures: undercut anchors must be selected; there is no alternative

  • Cracked concrete: undercut anchors or special reverse-cone chemical anchors must be selected

  • Tight schedules: undercut anchors are ready to use immediately upon installation, whereas chemical anchors require waiting for curing

  • Cost sensitivity: in non-load-bearing, uncracked concrete applications, expansion anchors may be considered

V. Daring Undercut Anchors — Safety Assurance for Load-Bearing Structures

Core product advantages

Daring undercut anchors takepure mechanical lockingas their core and have fully passed multiple authoritative tests:

  • Class S anchor certification: the highest-grade mechanical anchor suitable for cracked concrete and seismic zones

  • 2 million fatigue cycles: maintains stable anchoring force under cyclic loads

  • 120-minute fire resistance: retains load capacity in high-temperature environments

  • Seismic test: Passed the seismic test of the National Building Materials Testing Center; suitable for seismic zones

  • Mechanical properties test: Key indicators such as tensile strength and yield strength all meet the required standards

  • Corrosion protection test: coating thickness, salt spray, elongation, and thread precision testing

Size range

The Daring undercut anchor series coversM8-M20sizes, with materials coveringgrade 5.8 and 8.8 carbon steel (hot-dip galvanized ≥45 μm) and 304/316 stainless steel, and is supplied withfactory undercutting drill bits and electric installation tools, ensuring reaming quality. The products comply withJGJ 145-2013、GB 50367-2013and other code requirements.

6. FAQ

Q1Why are undercut anchors safer than both chemical anchors and expansion anchors?
Undercut anchors use pure mechanical interlock load transfer and rely on neither friction nor chemical bonding. Expansion anchors rely on friction (prone to loosening under vibration), chemical anchors rely on adhesive bonding (aging risk), while undercut anchors rely on the rigid interlock formed by reaming at the hole base. Their load capacity can reach 2-3 times that of expansion anchors, and their failure mode is anchor tensile rupture (with warning) rather than pull-out (without warning).
Q2Can undercut anchors be used in load-bearing structures?
Yes. According to GB 50367-2013, mechanical anchors used in load-bearing structures shall be undercut anchors with a keying effect. Expansion anchors and ordinary chemical anchors are strictly prohibited in load-bearing structures. Undercut anchors are the compliant choice for anchoring load-bearing structures.
Q3How much higher is the load capacity of undercut anchors than that of expansion anchors?
For the same size, the load capacity of undercut anchors can reach 2-3 times that of expansion anchors. Taking M12 as an example, the ultimate pull-out force of an expansion anchor is about 20 kN (anchor pull-out), while that of an undercut anchor is ≥43.8 kN (anchor tensile rupture).
Q4Why is the failure mode of undercut anchors safer?
The failure mode of an undercut anchor is anchor tensile rupture — a ductile failure with clear deformation warning before it occurs. The failure mode of an expansion anchor is anchor pull-out — a brittle failure that releases instantaneously without warning. A failure mode with warning gives engineers time to react and is therefore safer.
Q5What tests have Daring undercut anchors passed?
Daring undercut anchors have passed ETA certification, Class S anchor certification, 2 million fatigue cycles, 120-minute fire resistance, seismic testing, mechanical properties testing, coating thickness testing, salt spray testing, elongation and thread precision testing, and other authoritative certifications. The products comply with JGJ 145-2013 and GB 50367-2013.

Daring undercut anchors are built aroundpure mechanical interlockand have passed ETA certification, Class S anchor certification, 2 million fatigue cycles, 120-minute fire resistance, seismic testing, and other authoritative tests, making them the compliant choice for load-bearing structure anchoring. The series covers sizes M8-M20, with materials including grade 5.8 and 8.8 carbon steel (hot-dip galvanized ≥45 μm) and 304/316 stainless steel, and is supplied with factory undercutting drill bits and electric installation tools. For advice on undercut anchor selection and safety assessment for a specific project, please contact Daring's technical team.

References

Daring website — Undercut mechanical anchors product page

Daring website — Difference between expansion anchors and undercut anchors

Daring website — Detailed classification of mechanical anchors

GB 50367-2013, Code for Design of Strengthening Concrete Structures

JGJ 145-2013, Technical Specification for Post-Installed Anchorage in Concrete Structures

GB 50011, Code for Seismic Design of Buildings

Back to Daring Home  Back to Top