Product Knowledge

What is the installation torque for back bolts? How to control quality with a torque wrench

Views: 0Posted on: 2026-09-07

First, the conclusion:There is no single fixed value for back bolt installation torque; the torque requirements vary by size and material. Taking an M6 hammer-in back bolt as an example, the installation torque is typically4-6N·m; for an M8 hammer-in back bolt it is approximately8-10N·m; because screw-in back bolts are installed differently, torque control is more precise. The correct approach is to strictly follow theproduct technical data sheetand use aproperly calibrated torque wrenchto tighten in two steps — first pre-tighten to 50% of the specified torque, then tighten uniformly to the final torque value. Daring hammer-in back bolts have fully passed theTongji University rare-earthquake seismic test at intensity 9, and are supplied with a special hammer-in socket and torque wrench to ensure precise and controllable construction quality.

In back-bolt curtain wall projects, installation torque is one of the key factors determining the anchoring quality of back bolts. Too little torque prevents the back bolt from expanding fully, resulting in insufficient anchoring force; too much torque may damage the panel or cause cracking of the base material. Many construction workers lack a systematic understanding of the specific torque values and control methods for back bolt installation. This paper provides a comprehensive analysis from the perspectives of torque standards, influencing factors, operating methods and quality control.

I. Standard Values for Back Bolt Installation Torque

1.1 Reference torque values for different back bolt sizes

The following are reference installation torque values for common back bolt sizes (the product technical data sheet takes precedence):

Back bolt typeSizeReference installation torqueRemarks
Hammer-in back boltM64-6 N·mPanel thickness 25–30 mm
M88-10 N·mPanel thickness ≥ 30 mm
M1010-15 N·mLarge-size thick panels
Screw-in back boltM63-5 N·mSuitable for thin panels, with low installation stress
M85-8 N·mMedium-thickness panels

Note:The above are reference values; the actual installation torque should be based on the back bolt product technical data sheet, as torque requirements may differ among brands and models.

1.2 Main basis for torque standards

Back bolt installation torque is determined mainly on the basis of the following factors:

  • Back bolt size: different sizes such as M6, M8 and M10, with torque values increasing as the diameter grows

  • Back bolt type: hammer-in back bolts generally require higher torque than screw-in back bolts

  • Panel material and thickness: different materials such as granite, marble and ceramic panels have different torque requirements

  • Product technical requirements: products from every brand are supplied with detailed installation torque parameter tables

All brands provide detailed installation torque parameter tables, which must be consulted and strictly observed before construction.

II. Effect of Installation Torque on Anchoring Quality

2.1 Consequences of insufficient torque

Insufficient installation torque leads to the following problems:

  • Insufficient expansion: the expansion segments of a hammer-in back bolt or the expansion sleeve of a screw-in back bolt cannot fully deploy,so a mechanical lock cannot be established

  • Insufficient load-bearing capacity: the connection strength between the back bolt and the panel is far below the design value, and the pull-out test fails

  • Risk of long-term loosening: under wind loads and thermal stress, the back bolt may gradually loosen

2.2 Consequences of excessive torque

Excessive installation torque likewise has serious consequences:

  • Panel damage: excessive torque may cause the panel to developmicro-cracks or cracks at the back bolt hole

  • Damage to expansion segments/sleeve: over-tightening may deform the expansion segments or rupture the sleeve

  • Stress concentration: excessive installation stress creates stress concentration points inside the panel, reducing long-term durability

2.3 Correlation between improper torque and failed pull-out tests

Improper torque is animportant human factorin back bolt pull-out test failures. Insufficient installation torque prevents the back bolt from expanding fully, so it is pulled straight out during testing; excessive installation torque causes hidden cracks in the panel or damage to the expansion segments, resulting in abnormal failure during pull-out. According to JGJ 145-2013, when a pull-out test fails, the first thing to check is whetherthe construction torque complies with the product requirements。

III. Using a Torque Wrench to Control Construction Quality

3.1 Selection of a torque wrench

Back bolt installation should use apreset torque wrenchor adigital torque wrench:

  • Preset torque wrench: slips automatically once the set torque is reached, suitable for batch construction and simple to operate

  • Digital torque wrench: displays the torque value in real time with high precision, suitable for quality sampling and fine control

  • Torque range: should cover the required back bolt installation torque; for M6–M10 back bolts, a torque wrench with a2-20N·mrange covering the required torque is typically selected.

Daring supplies a dedicated torque wrench that can precisely control the installation torque of M6, M8, M10 and other back bolt sizes, ensuring construction quality.

3.2 Calibration and maintenance of torque wrenches

The precision of a torque wrench directly affects construction quality, so it must be calibrated regularly:

  • Calibration before first use: a new wrench should be calibrated on a standard torque tester before use

  • Periodic calibration: recommended every3–6 monthsor every5,000 usesof use, a calibration should be performed

  • Resetting after use: after each use, the torque wrench should be set to its lowest scale to preserve spring accuracy

  • Re-calibration after dropping or impact: if the wrench is dropped or subjected to impact, it must be recalibrated

Never use an uncalibrated torque wrench, and never substitute an ordinary wrench for a torque wrench.

3.3 Standard operating procedure

The standard procedure for using a torque wrench to control back bolt installation torque is as follows:

  • Step 1: Preset the torque— preset the target torque value on the torque wrench according to the back bolt technical data sheet

  • Step 2: Pre-tightening— use an ordinary wrench or power tool to tighten the nut to near the seated position (about 50% of the specified torque)

  • Step 3: Final tightening— tighten uniformly with the preset torque wrench and stop when the 'click' is heard

  • Step 4: Marking— after tightening, mark the contact point between the nut and washer to facilitate later inspection

Daring recommends adopting the'pre-tightening + final tightening'two-step method to avoid torque deviation caused by tightening in a single step. Daring supplies a dedicated torque wrench that can precisely control the installation torque of M6, M8, M10 and other back bolt sizes.

3.4 Torque control differences between hammer-in and screw-in back bolts

The two types of back bolts are controlled differently:

  • Hammer-in back bolt: after expansion is completed by hammering, the nut is tightened; the torque mainly serves a locking function,and over-tightening is not allowed. Refer to the product technical data sheet for specific torque values.

  • Screw-in back bolt: byrotating the threaded rod to expand the sleeve, the torque directly controls the degree of expansion and must be precisely maintained within the specified range. Too little torque results in inadequate expansion, while too much may damage the panel.

The installation torque of the Daring M12×80×130 undercut anchor is40N·m, that of the M16×100×160 is80N·mand that of the M20×160×260 is150N·m. Never use an uncalibrated torque wrench or tighten by feel.

IV. Common Questions About Back Bolt Installation Torque

4.1 Common torque problems in construction

SymptomPossible causeSolution
The nut cannot be tightened to the set torque valueDamaged threads or mismatched threadsCheck thread quality and replace with a qualified product
The nut continues to turn after the torque value is reachedIncorrect torque setting or a faulty wrenchReset the torque and check the wrench calibration
Abnormal noise from the panel during tighteningExcessive torque or hidden cracks in the panelStop immediately and investigate the cause
Pull-out test failsInsufficient torque or inadequate drilling accuracyCheck torque records and drilling quality

4.2 Key quality control points

  • Before construction: check the product technical data sheet, preset the torque value and verify the torque wrench calibration

  • During construction: strictly implement the 'pre-tightening + final tightening' two-step method; record the torque value immediately after each back bolt is completed; stop and investigate immediately if any abnormality is found

  • After construction: mark each tightened back bolt individually; carry out torque sampling inspection by inspection lot (sampling ratio ≥ 10%)

  • Torque sampling inspection: re-tighten with a torque wrench for inspection; if the wrench turns before reaching the preset torque, that back bolt has insufficient torque and must be reinstalled

V. Normative Basis

Control of back bolt installation torque should meet the following specification requirements:

  • JGJ 145-2013'Technical Specification for Post-installed Anchoring of Concrete Structures' — quality requirements for post-installed anchoring construction

  • JGJ 336-2016'Technical Code for Engineering of Artificial Panel Curtain Walls' — back bolt installation and construction requirements

  • JG/T 160-2017'Mechanical Anchors for Concrete' — anchor installation torque requirements

  • Product technical data sheet— specific torque requirements for back bolts of each brand

VI. Daring Back Bolt Installation Torque Solutions

6.1 Product advantages

The Daring back bolt series strictly follows product technical standards and is supplied with complete installation tools:

  • Precise torque parameters: every back bolt product is provided with a detailed installation torque parameter table

  • Dedicated torque wrench: a calibrated torque wrench is supplied, covering sizes M6–M10

  • Hammer-in socket: special square- or round-shank hammer-in sockets for faster and safer installation

  • Seismic verification: Daring hammer-in back bolts have fully passed the Tongji University rare-earthquake seismic test at intensity 9, with acceleration reaching 1.24g

6.2 Construction support

Daring provides full-process service fromproduct selection and technical briefing to on-site construction guidance, including confirmation of installation torque parameters and training in the use of torque wrenches. For back bolt installation torque parameters and construction recommendations for specific projects, please consult the Daring technical team.

VII. Frequently Asked Questions

Q1What is the installation torque of an M6 hammer-in back bolt?
The installation torque of an M6 hammer-in back bolt is typically 4–6 N·m; the product technical data sheet takes precedence. Daring supplies a dedicated torque wrench that can precisely control the installation torque.
Q2What are the consequences of excessive installation torque?
Excessive torque can cause micro-cracks or cracking in the panel at the back bolt hole, and may also deform the expansion segments or rupture the sleeve, creating stress concentration and reducing long-term durability. The product technical data sheet should be followed strictly.
Q3How can you determine whether the back bolt installation torque is acceptable?
With a preset torque wrench, automatic slipping once the set value is reached indicates acceptance; after construction, torque sampling inspection may be carried out with a torque wrench (sampling ratio ≥ 10%), and if the wrench turns before reaching the preset torque, the back bolt must be reinstalled.
Q4Does a torque wrench need regular calibration?
Yes. Calibration is recommended every 3–6 months or every 5,000 uses. After each use, the torque wrench should be set to its lowest scale, and it must be recalibrated after being dropped or subjected to impact. Never use an uncalibrated torque wrench.
Q5What are the characteristics of the installation torque of Daring back bolts?
Every Daring back bolt product is provided with a detailed installation torque parameter table and a calibrated dedicated torque wrench. Daring hammer-in back bolts have fully passed the Tongji University rare-earthquake seismic test at intensity 9, ensuring anchoring safety when installed with the correct torque.

The Daring back bolt series covers hammer-in, screw-in, cast-in and high-load back bolts, made of 304/316 stainless steel and supplied withdedicated torque wrenches and hammer-in sockets, with a detailed installation torque parameter table for every product. Daring hammer-in back bolts have fully passed theTongji University rare-earthquake seismic test at intensity 9. For back bolt installation torque parameters and construction recommendations for specific projects, please consult the Daring technical team.

References

Daring official website — technical parameters of the back bolt series

JGJ 145-2013, 'Technical Specification for Post-installed Anchoring of Concrete Structures'

JGJ 336-2016, 'Technical Code for Engineering of Artificial Panel Curtain Walls'

JG/T 160-2017, 'Mechanical Anchors for Concrete'

Back to Daring Home  Back to Top