Product Knowledge

Concrete screw anchor installation method and precautions: three steps to install

Views: 0Posted on: 2026-08-20

To start with the conclusion:The installation method for concrete screw anchors is very simple, with onlythree core steps:drilling → hole cleaning → screwing in the anchor. Unlike chemical anchors, screw anchorsrequire no curing wait, and it carries load as soon as it is screwed in. The Daring cone-cylinder self-cutting anchor is made ofcarbon steel of grade 12.9 or higher, which can be fully removed after installation and used for temporary anchoring. However, note that concrete screw anchorsdoes not belong to the anchor systemand must not be designed as anchors for load-bearing structures.

The concrete screw anchor is a new type of mechanical anchoring product whose anchoring principle resembles driving a self-tapping screw into wood — the hard threads on the anchor's outer wall cut into the concrete, carving threaded grooves in the hole wall to complete the anchoring. JG/T 160-2017 Mechanical Anchors for Concrete, implemented on December 1, 2017, brought screw anchors into the standards system for the first time. Based on CECS 400:2015 Technical Specification for Application of Self-Tapping Anchors and JG/T 160-2017, this article systematically explains the installation methods and precautions for concrete screw anchors.

I. Installation Steps for Concrete Screw Anchors

The installation method for concrete screw anchors is very simple, mainly divided into the following three steps:

Step 1: Drilling

Usea straight-hole drill bitto drill a hole of the corresponding diameter and depth in the concrete base material. Note the following points when drilling:

  • Drill bit selection: the drill bit and matching tools specified in the product manual must be used

  • Drilling depth: follow the drilling depth specified in the product manual; only positive deviation in hole depth is allowed, and it should not exceed 5mm

  • Drilling diameter: the diameter deviation should not exceed the value specified by the standards, and there should be no negative deviation

  • Perpendicularity: the perpendicularity deviation should not exceed 2.0%

  • Position deviation: the position deviation should comply with the construction drawings; if unspecified, it should not exceed 5mm

Before drilling, use a concrete cover meter to determine the rebar distribution in the structure; where rebar is encountered, the drilling position may be adjusted as appropriate within the constrained working space.

Step 2: Hole cleaning

Usea dust bloweraimed at the hole to blow out dust until no dust escapes from the hole. The specific hole cleaning requirements are as follows:

  • Cleaning method: compressed air or a hand pump should be used to remove dust and debris from the hole

  • Cleaning standard: the base material surface should be smooth and even, with no residual dust or debris

  • Temporary sealing: if the anchor is not installed immediately after hole cleaning, the hole opening should be temporarily sealed to prevent dust, debris, oil, and moisture from entering and affecting anchoring quality

Step 3: Screwing in the anchor

Usea torque electric drillto screw the concrete screw anchor into the hole, completing the anchoring. Key installation points are as follows:

  • Driving method: as the anchor is driven into the installation hole, its threads cut into the base material to achieve anchoring

  • Checking full installation: the anchor is correctly installed when its head is flush with the fixture and cannot be driven any deeper

  • Immediate loading: no curing time is needed once fully installed; the anchor carries load immediately upon driving

Installing the Daring cone-cylinder self-cutting anchor is especially easy —helical, stress-free installation, simple to operate, with outstanding performance in fast anchoring at small edge distances and small spacings. The anchor rod, washer, and hex socket head form a single integral unit; the threads cut directly into the base material when driven to achieve anchoring.

II. Installation Precautions

2.1 Hole cleaning: requirements vary by condition

The hole cleaning requirements for concrete screw anchorsvary with the installation position:

  • Vertical installation (ceiling and floor): products from some brands do not require hole cleaning

  • General conditions: hole cleaning according to the standard requirements is recommended to ensure anchoring quality

The installation process of the Daring cone-cylinder self-cutting anchor is relatively forgiving, but basic hole cleaning is still recommended to ensure the best anchoring performance.

2.2 Torque: no precise control needed

Installing concrete screw anchorshas no strict torque requirement, placing low demands on installers. Simply drive the anchor into place with a torque electric drill; there is no need to wait for curing as with chemical anchors, nor to perform secondary reaming as with undercut anchors.

2.3 Precautions for high-strength concrete

Concrete comes in many types. If the anchor is to be used inhigh-strength concrete (such as C60), where the installation torque requirement is relatively high, inform the supplier of the working conditions and let the supplier choosea product with teeth of the corresponding height, to avoid excessive installation difficulty.

2.4 Ambient Temperature and Weather Requirements

According to the specifications:

  • Temperature requirement: the ambient temperature at the anchor installation site should generally not be lower than-5℃

  • Weather requirement: outdoor work in rain or snow is strictly prohibited

2.5 Anchor Inspection and Acceptance

The following checks should be performed during and after installation:

  • Tool check: for each anchor type, check at least once that the drilling tools meet the product manual requirements

  • Hole cleaning check: inspect the cleaning of every anchor hole

  • Installation check: visually verify that each anchor is fully seated

3. Product Features of the Daring Cone-Cylinder Self-Cutting Anchor

FeatureDescription
High-strength materialGrade 12.9 or higher carbon steel, ensuring the threads are not damaged when cutting into concrete
Screw-in installationStress-free installation with simple operation
Removable designCan be fully removed after installation, suitable for temporary anchoring
Immediate load bearingNo curing wait once the anchor is in place
Suitable for multiple base materialsCracked concrete, non-cracked concrete, and natural stone
Stainless steel option available410 stainless steel, 120-hour salt spray test

IV. FAQs

Q1Do concrete screw anchors require hole cleaning?
Hole cleaning is generally recommended. Use a dust blower aimed at the hole to blow out dust until no dust escapes from the hole. For vertical installation (ceiling and floor), products from some brands do not require hole cleaning.
Q2How much torque is needed to install concrete screw anchors?
Screw anchors have no strict torque requirement; simply drive them in with a torque electric drill. Correct installation is achieved when the anchor head is flush with the fixture and cannot be driven any deeper.
Q3Can concrete screw anchors be used in load-bearing structures?
No. Screw anchors do not belong to the anchor system and must not be designed as anchors. Mechanical anchors for load-bearing structures should be undercut anchors with an interlock effect.
Q4Can the Daring cone-cylinder self-cutting anchor be removed?
Yes. The Daring cone-cylinder self-cutting anchor can be fully removed after installation and used for temporary anchoring. Simply reverse the torque electric drill to unscrew the anchor.
Q5What base materials are concrete screw anchors suitable for?
The Daring cone-cylinder self-cutting anchor is suitable for base materials such as cracked concrete, non-cracked concrete, and natural stone. It is not suitable for post-installed connections in masonry or lightweight aggregate concrete base materials.

The Daring mechanical anchor series covers post-installed undercut, self-undercutting, drop-in, Anka, and heavy-duty mechanical anchors, made of carbon steel / stainless steel with multi-layer coating processes. Mechanical locking achieves instant fixation upon installation with no curing required; high load capacity with seismic and fatigue resistance suits cracked / non-cracked concrete, natural stone, and other base materials. They are widely used in curtain walls, steel structures, heavy equipment, rail transit, tunnels and utility tunnels, and various other anchoring scenarios. For concrete screw anchor selection and installation advice on a specific project, please contact the Daring technical team.

References

Daring website — How to Use Concrete Screw Anchors (with diagrams)(three-step installation method)

Daring website — Cone-Cylinder Self-Cutting Anchor product page(Grade 12.9 material, removable, suitable for multiple base materials)

Daring website — Concrete Screw Anchors: A New Type of Anchoring Product(anchoring principle and standard basis)

CECS 400:2015 Technical Specification for Application of Self-Tapping Anchors — installation and acceptance of self-tapping anchors

JG/T 160-2017 Mechanical Anchors for Concrete — special tests and requirements for screw anchors

JGJ 145-2013 Technical Specification for Post-Installed Fastenings in Concrete Structures — anchor installation requirements

Back to Daring Home  Back to Top