Product Knowledge

M12 chemical anchor specifications and pull-out capacity explained

Views: 0Posted on: 2026-08-19

To start with the conclusion:The M12 chemical anchor isone of the most widely used and most broadly appliedchemical anchor specifications in building post-installed anchoring projects. Taking the Grade 5.8 carbon steel M12×160 chemical anchor as an example, under standard installation the hole diameter isФ14mmand the drilling depth is110mm, with a design tensile load in C30 concrete of about14.5-19.8kN, and a failure tensile load of>43.8kN. When selecting, pay close attention toanchor strength grade, base material strength, and installation quality, the three major factors.Curtain wall load-bearing structures must use special reverse-cone chemical anchors; ordinary M12 chemical anchors are strictly prohibited for curtain wall load-bearing.

The M12 chemical anchor is one of the most commonly used anchoring products in building post-installed anchoring projects, widely used for equipment fixing, curtain wall structural member anchoring, pipe support installation, and similar applications. Many designers and installers lack a systematic understanding of M12 chemical anchor specifications and pull-out force data. This article provides a comprehensive analysis covering specifications, technical parameters, pull-out force data, and influencing factors.

I. Specifications and Models of M12 Chemical Anchors

In M12 chemical anchors, "M12" denotes a nominal rod diameter of 12mm. The most common specification on the market isM12×160, where 160mm represents the total rod length.

The main specifications of Daring M12 chemical anchors are as follows:

ModelRod diameter (mm)Total rod length (mm)Drilling diameter (mm)Drilling depth (mm)Maximum anchorage thickness (mm)
M12×16012160Ф1411025

M12×160 is the most mainstream specification on the market, with a drilling depth of 110mm, a drilling diameter of 14mm, and a maximum anchorage thickness of 25mm.

II. Key Technical Parameters of M12 Chemical Anchors

The core technical parameters of M12 chemical anchors include drilling diameter, drilling depth, anchorage length, design load, and failure load.

ParameterM12×160
Drilling diameterФ14mm
Drilling depth110mm
Anchorage length110mm
Design tensile loadAbout 10-15kN
Failure tensile load≥43.8kN
Design shear loadAbout 5-10kN
Failure shear load≥25.4kN

III. Measured Pull-Out Force Data for M12 Chemical Anchors

The pull-out force of M12 chemical anchors is affected by multiple factors. Measured data under different conditions are as follows:

3.1 Pull-Out Force Under Standard Installation Conditions

Taking the Daring Grade 5.8 carbon steel M12×160 high-strength chemical anchor with matching chemical capsules as an example, under standard installation conditions (thorough hole cleaning):

  • Ultimate pull-out force: up to 50kN or more, with test results showing tensile failure of the anchor rod

  • C30 concrete pull-out force reference: about 36-40kN

  • Characteristic failure tensile load:≥43.8kN

  • Design tensile load value: 5-10kN (safety factor of about 2.5-3.0)

3.2 Pull-Out Force Comparison with Incomplete Hole Cleaning

Installation quality has an extremely significant impact on the pull-out force of M12 chemical anchors:

  • Standard hole cleaning: pull-out force can reach45-50kN

  • Without hole cleaning or dust blowing: overall load capacity drops by abouthalf, about 25kN

With a margin factor of 2.5, the design value must be kept below 10kN to be safe when hole cleaning is incomplete; in practice, however, design values are mostly 10-13kN, raising concerns about overall structural safety.

3.3 Pull-Out Force Under Different Base Material Strengths

The strength of the base concrete directly affects the pull-out force:

  • C25 concrete: pull-out force limit of about36kN(anchorage depth of 110mm)

  • C30 concrete: pull-out force limit ofover 40kN(anchorage depth of 110mm)

IV. Materials and Surface Treatment of M12 Chemical Anchors

Daring M12 chemical anchors are available in various materials and surface treatments:

Material gradeYield strengthSurface treatmentApplication scenario
Grade 5.8 carbon steel≥400MPaElectro-galvanized / hot-dip galvanizedGeneral indoor environments
Grade 8.8 carbon steel≥640MPaElectro-galvanized / hot-dip galvanizedHigh load capacity requirements
304 stainless steel≥700MPa(A2-70)No treatment requiredGeneral corrosive environments
316 stainless steel≥700MPa(A4-70)No treatment requiredCoastal / highly corrosive environments

Daring M12 chemical anchors are made of carbon steel of Grade 5.8 or above or 304/316 stainless steel, paired with the corresponding chemical capsule model. High-strength rods of Grade 5.8 or above have a yield strength of up to 400MPa.

V. Matching Products for M12 Chemical Anchors

Daring M12 chemical anchors are used with the following matching products:

  • Chemical capsule: free of any diluents, with rapid curing in 30 minutes and good mechanical properties

  • Dedicated installation head: Daring ships the corresponding installation head with the order; simply clamp the installation head with a torque tool and screw the chemical anchor into the hole

  • Injection anchoring adhesive: Daring's DL-200E modified epoxy injection anchoring adhesive meeting the national Grade A adhesive standard, with strong bond anchoring force, temperature resistance, and seismic performance

VI. Selection Considerations for M12 Chemical Anchors

6.1 Misconceptions About Embedment Depth

Taking the Grade 5.8 M12 chemical anchor as an example, the national standard embedment depth is 110mm, and pull-out tests in C30 concrete ended in tensile failure of the rod, indicating that a 110mm embedment depth fully exploits the ultimate mechanical properties of the anchor material (Grade 35 steel). For small specifications (M16 and below), there is no need whatsoever to increase the embedment depth; forcing an increase only adds cost and workload.

6.2 Difference Between Design Values and Failure Values

There is a safety factor of about 2.5-3.0 between the design tensile load (about 10-15kN) and the failure tensile load (about 43.8kN) of M12 chemical anchors. Design must be based onthe design value as the criterion, not the failure value.

6.3 Core Advantages of Daring M12 Chemical Anchors

  • Pull-out force: M12 chemical anchors achieve a pull-out force of over 50kN, a first-tier market level

  • Chemical capsule: free of any diluents, with rapid curing in 1 hour

  • Fire resistance: passed the 120-minute fire resistance test at the National Building Materials Testing Center

  • Customization service: supplied chemical anchors as large as M56×1500 for nuclear power projects

VII. FAQs

Q1What are the drilling diameter and depth for M12 chemical anchors?
For the M12×160 specification, the drilling diameter is Ф14mm and the drilling depth is 110mm.
Q2How much pull-out force can an M12 chemical anchor achieve?
Under standard installation, the Daring Grade 5.8 carbon steel M12×160 chemical anchor achieves an ultimate pull-out force of over 50kN. The characteristic failure tensile load is about 43.8kN, and the pull-out force limit in C30 concrete is about 40kN.
Q3What is the difference between the design tensile load and the failure tensile load of an M12 chemical anchor?
The design tensile load is the allowable service value after applying a safety factor, about 10-15kN; the failure tensile load is the load at which the anchor reaches ultimate failure, about 43.8kN. Designs must be based on the design value.
Q4Can M12 chemical anchors be used for curtain wall load-bearing?
Ordinary M12 chemical anchors (high-strength chemical anchors) are strictly prohibited in curtain wall load-bearing structures. Load-bearing structures should use special reverse-cone chemical anchors or undercut mechanical anchors.
Q5How much does incomplete hole cleaning affect the pull-out force?
The impact is enormous. Without hole cleaning and dust blowing, the overall load capacity can drop by about half. With standard hole cleaning, the pull-out force reaches 45-50kN; without cleaning, it falls to about 25kN.

The Daring chemical anchor series covers high-strength, capsule, special reverse-cone, and dynamic-load reverse-cone anchors, paired with Daring's DL-200E modified epoxy injection anchoring adhesive meeting the national Grade A adhesive standard, available in carbon steel of Grade 5.8 or above, or in 304/316 stainless steel. Daring M12 chemical anchors offer strong bond anchoring force, temperature resistance, and seismic performance, with stable anchoring under static and dynamic loads. For M12 chemical anchor selection advice on a specific project, please contact the Daring technical team.

References

1. Daring website — What Are the Chemical Anchor Specifications and Models(M12 chemical anchor specification parameter table)

2. Daring website — Differences Between Chemical Anchors and Expansion Anchors(measured pull-out force data of M12 chemical anchors above 60kN)

3. Daring website — High-Strength Chemical Anchor product page(materials and specification parameters)

4. JGJ 145-2013 Technical Specification for Post-Installed Fastenings in Concrete Structures(national industry standard)

5. Industry-common technical parameter data for chemical anchors (design load and failure load of M12 chemical anchors)

Back to Daring Home  Back to Top