Product Knowledge

Which is safer, a slot-cut pendant or a back bolt pendant?

Views: 0Posted on: 2026-08-14

To start with the conclusion:In stone curtain wall dry-hung cladding systems, back bolt pendants are safer than slotted pendants. Back bolt pendants use mechanical locking, with panels bearing load independently and the anchoring point located on the back of the panel, providing good impact resistance; slotted pendants use chemical adhesive fixing, where the stone bears load through slots cut in its edges. The slotted area is the weakest part of the stone and carries safety risks such as stress concentration and adhesive aging.For projects with high safety requirements, back bolt pendants should be the preferred choice.

1. Basic overview of the two pendant types

In stone curtain wall projects, the dry-hung connection method directly affects the structural safety and service life of the curtain wall. The mainstream dry-hanging methods fall into two categories, slot type and back bolt type, with corresponding slot pendants and back bolt pendants. So which of these two pendant types is safer? This article provides a systematic comparison in terms of load principles, connection method, durability, and seismic performance.

1.1 Slot pendants (slot-type dry-hanging)

A slot pendant works byslotting the edge of the stone and inserting the pendant into the slot, then bonding it to the stone with a special adhesive (marble adhesive or structural adhesive). Common slot pendants include SE pendants and pin-type pendants.

Slotted dry-hung cladding is currently one of the most widely used connection methods for stone curtain walls in China. During construction, a slot is cut into the side or end face of the stone, the pendant is inserted into the slot and fixed with adhesive, and the pendant is then connected to the framing.

1.2 Back bolt pendants (back bolt dry-hung cladding)

The back bolt pendant works by drilling and reaming a hole in the back of the stone, mechanically locking the back bolt inside the stone, and then connecting the stone to the framing through the matching pendant. Back bolt pendants work on a physical locking principle and do not rely on any adhesive.

Back bolt dry-hung cladding uses a cylinder-cone drill bit and dedicated equipment to drill into the back of the stone, creating an undercut at the bottom of the hole. After the back bolt is inserted, torque or hammering expands the expansion ring, forming a convex engagement with the bottom of the hole and achieving mechanical locking. The main difference between back bolt pendants and slotted pendants is that the anchoring point of the back bolt pendant is located on the back of the panel rather than on the edge.

Suggested image: a comparison diagram of the load-bearing principles of the slotted and back bolt systems (marking load directions and weak points)

2. Comprehensive safety comparison

Comparison dimensionBack bolt pendantsSlotted pendants
Connection principleMechanical locking (physical anchoring)Chemical adhesive fixing
Load-bearing locationBack of the panel (not a weak area)Slotted area at the panel edge (weakest area)
Load-bearing modePanels bear load independentlyPanels overlap one another, with stress concentration
DurabilityStainless steel, 50-year warrantyAdhesives carry an aging risk
Impact resistanceHighLow
Structural deformation capacityYesNo (rigid connection)
Replacement and maintenancePanels can be replaced individuallyReplacement is difficult
Safety risksExtremely low safety risksSlot cracking, adhesive failure, chipped corners, and fracturing

3. Five reasons why back bolt pendants are safer

Reason 1: Mechanical locking vs. chemical bonding

Back bolt pendants work on a mechanical locking principle: anchoring is achieved through the physical interlock between the back bolt's expansion ring and the undercut hole in the stone, which is "physical locking". Slotted pendants rely on chemical adhesives to bond the pendant to the stone, which is "chemical bonding".

The essential difference between the two: mechanical locking does not suffer aging, and the bond strength remains stable over the long term; chemical bonding carries the risk of adhesive aging and degradation — under ultraviolet light, acid rain, and temperature variations, organic adhesives age and become brittle, making their long-term reliability hard to guarantee. Some inferior adhesives may age and embrittle within just a few years in outdoor environments, causing pendants to fall off.

Reason 2: Independent panel loading vs. stress concentration

Back bolt pendants allow each stone panel to bear load independently, with no mutual influence between panels. The back bolt anchoring point is located on the back of the panel, and loads are transferred directly to the framing through the back bolt, giving a clear load path.

Because slotted pendants require slots to be cut in the stone edges, the stone thickness at the slot is reduced to less than one third of the original, making it the weakest part of the stone. Under load, stress concentrates at the slot edges, which can easily cause chipped stone corners, slot cracking, or even fracturing. In slotted connections the panels overlap one another, and stress concentration further increases the risk of slot cracking.

Suggested image: a photo or stress analysis diagram of stone fracture caused by stress concentration at a slot (with the fracture point circled in red)

Reason 3: Superior impact resistance

The load-bearing area of the back bolt pendant is behind the panel, so under external forces the back bolt and the stone bear load as one unit, providing good impact resistance.

The load-bearing area of the slotted pendant is at the panel edge, and the slotted area is itself the weakest part of the stone. Under external forces, the edge slots can easily chip or crack. Especially under extreme conditions such as strong winds and earthquakes, the safety risk of slotted connections is significantly higher than that of back bolt systems.

Reason 4: Three-dimensional adjustment and structural deformation capacity

The back bolt pendant system has three-dimensional adjustment capability and structural deformation capacity, allowing it to accommodate thermal expansion and contraction caused by temperature changes and to effectively absorb deformations produced by horizontal loads such as earthquakes.

Slotted pendants form a rigid connection whose structure has no deformation capacity. Under thermal stress or seismic action, rigid connections can easily cause stone cracking or pendant failure. In actual construction, the slots are sometimes enlarged to adjust panel positions, further increasing safety risks.

Reason 5: Independent replacement and easy maintenance

In the back bolt pendant system, each stone panel can be installed and replaced independently, making maintenance easy. When a stone panel is damaged, it can be replaced individually without affecting the surrounding panels.

After slotted pendants "glue" the stone panels together, the entire curtain wall becomes a single unit. If one stone panel develops a crack or is damaged, it may affect multiple surrounding panels, making repair and replacement extremely difficult.

Suggested image: a cross-section diagram showing back bolt undercut locking on the back of the stone

4. Main safety risks of slotted pendants

Safety riskRisk description
Slot crackingCutting slots in the stone edges greatly weakens strength, and stress concentration can easily lead to slot cracking
Adhesive agingOrganic adhesives risk aging and embrittlement under ultraviolet light, acid rain, and temperature variations
Risk of enlarged slotsOn site, slots may be enlarged to adjust panel positions, severely weakening connection strength
Uncontrollable bonding qualityAdhesive volume, application technique, and curing conditions all affect bond quality, and on-site workmanship is hard to guarantee

5. Selection recommendations

Cases where back bolt pendants are preferred

  • High-rise building curtain walls: high wind loads and strict connection safety requirements
  • High seismic intensity zones: back bolt pendants offer good seismic performance and deformation capacity
  • Large stone panels: heavy panels demand high single-point load capacity
  • Projects with high safety requirements: densely occupied places such as hospitals, schools, and public transport
  • Projects seeking long-term durability: back bolt pendants use stainless steel with warranties of up to 50 years

Where are slot pendants still applied?

Slot pendants still have value in the following specific scenarios:

  • Low-rise buildings: projects with low building height and small wind loads
  • Temporary buildings: temporary buildings with no high service life requirements
  • Non-primary facades: decorative areas with relatively low safety requirements

However, it must be pointed out that the safety risks of slot pendants cannot be ignored; slot position, depth, and adhesive quality must be strictly controlled in use. Where safety matters, back bolt pendants are recommended.

Core principle: for curtain wall projects with high safety and durability requirements, prefer back bolt pendants; slot pendants should be used cautiously only in specific scenarios where safety risks are controlled and service life requirements are modest.

6. Frequently asked questions

Q1Why do slot pendants pose safety risks?
Slot pendants require slotting the stone edge, the weakest part of the stone, where strength drops sharply after the section is thinned by slotting. Since the connection relies on organic adhesives, there are aging and embrittlement risks under UV exposure, acid rain, and temperature differences, and stress concentrations under load can crack the slot or even shatter the stone.
Q2Why are back bolt pendants safer?
Back bolt pendants use a mechanical locking principle with the anchoring point on the back of the panel, so the effective cross-section of the stone is not weakened; each stone panel bears load independently with no stress concentration; the back bolt is stainless steel with no aging issues; and the system offers three-dimensional adjustment and deformation capacity to accommodate temperature changes and seismic loads.
Q3Are back bolt pendants more costly?
Back bolt pendants have slightly higher material and installation costs than slot pendants. But once the adhesive in a slot system ages and fails, repair often requires dismantling an entire wall, whereas a back bolt system allows individual panels to be replaced. Over a 20-year service life, the overall maintenance cost of the back bolt system is far lower than the slot system. Especially in projects with high safety requirements, back bolt pendants offer better life-cycle value.
Q4Are slot pendants being phased out?
As buildings grow taller and safety standards keep rising, the share of slot pendants in high-end curtain wall projects is indeed declining. They are still used in scenarios with modest safety requirements, such as low-rise and temporary buildings. For projects with safety requirements, back bolt pendants are recommended.
Q5What back bolt pendant products does Daring offer?
Daring offers a full range of aluminium alloy pendants, including ear-type, Type C (male-and-female), and H-type, matched with hammer-in and screw-in back bolts and dedicated drilling machines, with one-stop service from product selection and connection detail design to on-site technical support. All products have passed the Tongji University rare-earthquake intensity-9 seismic test, ensuring safe and reliable curtain wall projects.

7. Summary

Comparison itemBack bolt pendantSlot pendant
Connection reliabilityHigh (mechanical locking)Low (adhesive bonding, aging risk)
Load safetyHigh (rear loading, independent bearing)Low (edge loading, stress concentration)
DurabilityExcellent (stainless steel, 50-year warranty)Poor (adhesives degrade)
Seismic performanceExcellent (deformation capacity)Poor (rigid connection)
Maintenance and replacementConvenient (panels can be replaced individually)Difficult
Safety levelHighLow

Core conclusions:

  1. Safety: Back bolt pendants use mechanical locking, panels bear load independently, and there is no risk of adhesive aging, so their safety is significantly better than that of slotted pendants
  2. Durability: Back bolt pendants are made of stainless steel with a warranty of up to 50 years, while slotted pendants rely on adhesives and carry a hidden risk of long-term aging
  3. Seismic performance: Back bolt pendants have structural deformation capacity, giving them better seismic performance than rigidly connected slotted pendants
  4. Selection principle: For curtain wall projects with requirements for safety and durability, back bolt pendants should be the preferred choice

Daring offers a full range of aluminium alloy pendants, including ear-type, C-type (male-and-female), and H-type pendants, together with hammer-in and screw-in back bolts and dedicated drilling machines, providing one-stop service from product selection and joint design to on-site technical support. The back bolt pendant system has passed the seismic test under rare earthquakes of intensity 9 conducted at Tongji University, providing reliable protection for curtain wall safety. For pendant selection advice for a specific project, please contact the Daring technical team.

References

1. Daring official website — How to choose aluminium alloy pendants for back bolts(pendant types and compatibility notes)

2. Daring official website — An overview of curtain wall back bolt pendants(pendant functions and selection guide)

3. Daring official website — Male-and-female pendant product page(product parameters and material description)

4. Patent literature on fixing devices for dry-hung stone curtain walls (technical principle of back bolt pendants)

Back to Daring Home  Back to Top