Product Knowledge

How does hammer-in back bolt installation differ from screw-in back bolts

Views: 0Posted on: 2026-08-11

Conclusion first:The hammer-in back bolt useshammer strikeinstallation, suitable for panels thicker than 25 mm, with large hole tolerance and simple construction; the screw-in back bolt useselectric or manual screwinginstallation, suitable for thin panels thicker than 12 mm.Use hammer-in whenever possible, because of its larger hole tolerance and higher safety factor.

In stone curtain wall projects, back bolt selection and installation technique directly affect the safety and construction efficiency of the entire curtain wall system. The mainstream back bolt products on the market are hammer-in, screw-in and anti-loosening types. Among them, hammer-in back bolts account formore than 80%. So what are the differences in installation technique between hammer-in and screw-in back bolts? This article systematically compares them from five dimensions.

I. Different installation principles

The core difference between the two back bolts lies in theDifferent expansion methods。

Hammer-in back boltinstallation principle is:Shank stationary, expansion sleeve moves. Using the wedge-shaped inclined surface at the front of the shank, hammering expands the expansion part (expansion ring or plum-shaped expansion segment) to create friction against the inner wall of the back bolt hole. As the expansion body of a hammer-in back bolt expands, its upper diameter decreases and its lower diameter increases, changing from a cylindrical surface to a conical surface, forming a stress-free concentric engagement with the undercut conical hole in the stone.

Screw-in back boltinstallation principle is:The shank expands the expansion part from inside the expansion sleeve. The shank rotates and advances while the expansion sleeve expands slowly. During installation, the expansion sleeve is placed into the wedge-shaped hole, and a controllable stress-free anchoring structure is formed by rotating the shank. The upper edge of a screw-in back bolt is hexagonal, and it consists of an expansion sleeve with internal threads at the tail fin, an internal hex shank and a flange stop nut.

Comparison dimensionHammer-in back boltScrew-in back bolt
Installation principleShank stationary, expansion sleeve movesShank rotates, expansion sleeve expands
Installation methodmanual hammeringelectric or manual screwing
Expansion methodhammering expands the wedge surfacerotating shank expands slowly

II. Different construction steps

Hammer-in back bolt installation steps:

  1. Preparation: remove the flat washer, spring washer and nut of the back bolt and set aside, then place the shank and sleeve into the back bolt hole.

  2. Hammering: fit the driving sleeve over the shank and strike it with a hammer until the back bolt sleeve is flush with the panel.

  3. Place pendant: place the flexible gasket and matching aluminium alloy pendant onto the back bolt.

  4. Tighten: install the flat washer and spring washer, then tighten the nut.

Note: after installation, the shank of the back bolt must beexposed at least 3 mmto ensure the assembly does not come loose.

Screw-in back bolt installation steps(taking a three-piece back bolt as an example):

  1. Preparation: remove the flange nut of the back bolt and set aside, then place the set screw and back bolt head into the hole (with the hexagonal part of the head exposed).

  2. Screwing in: hold the hexagonal part of the back bolt head with a wrench, then screw in the set screw using a torque drill or hex key.

  3. Place pendant: place the flexible gasket and matching aluminium alloy pendant onto the back bolt.

  4. Tighten: simply screw in the flange nut.

Note: when installing a three-piece back bolt, it iseasy to punch through the panel, and requires some experience on the part of the installer to reduce panel breakage.

Comparison dimensionHammer-in back boltScrew-in back bolt
Core toolshammer + driving sleevetorque drill + hex key/hex wrench
Installation difficultySimpleMore complex
Key riskhammering stress damages thin panelseasy to punch through panels

III. Different applicable panels

Hammer-in back bolt: applicable topanels 25 mm and thicker. Daring hammer-in back bolts can be used on panels 20 mm and above and are more friendly to relatively hard panels. Hammer-in back bolts anchor by hammer expansion and are suitable for thick panels and ceramics. Common sizes are M6/M8, with embedment depths of 15 mm and 18 mm.

Screw-in back bolt: applicable tothin panels, and can be installed in panels as thin as 12 mm. Screw-in back bolts form a controllable stress-free anchoring structure by rotating the shank, so panels are less likely to be damaged; they are suitable for thin panels and ceramics. Screw-in back bolts are mostly used for installing thin panels such as ceramic tiles and vitrified tiles.

Comparison dimensionHammer-in back boltScrew-in back bolt
Applicable panel thickness≥25 mm (Daring can be used for ≥20 mm)≥12mm
Typical applicationsstone curtain walls, hard panelsthin panels such as ceramic tiles and vitrified tiles
Panel rangeNarrow; cannot be used for thin panelsSuitable for panels of all thicknesses

IV. Different drilling accuracy requirements

This is themost fundamental difference。

Hammer-in back bolt:offers a larger hole tolerance. Compared with screw-in back bolts, hammer-in back bolts have lower requirements for panel drilling, simpler construction and higher safety. Daring hammer-in back bolts have a large hole tolerance and asafety factor increased by 80%。

Screw-in back bolt:has very strict hole requirements. The expansion part of a screw-in back bolt is very small; the radius difference before and after expansion may be only about 0.5 mm, so the requirements for the back bolt hole are very strict. If the straight hole is too small the bolt cannot be inserted; if slightly too large it is easily pulled out. If the dovetail groove diameter is too small, the expansion sleeve cannot expand fully, resulting in insufficient pull-out resistance.

Comparison dimensionHammer-in back boltScrew-in back bolt
Hole diameter toleranceLargeSmall
Construction toleranceHighLow
Requirements for installersRelatively lowRelatively high
Safety factorHigher—

V. Different supporting tools and pendants

Hammer-in back bolt: consists of a tapered shank, a plum-shaped expansion ring (or expansion ring), a sleeve, a flat washer, a spring washer and a hex nut. It is installed with a matching driving sleeve. The matching aluminium alloy pendants are mainlyflat-ear pendantsandmale-and-female pendants (C-type pendants). Flat-ear pendants offer better cost-effectiveness and are more widely used in projects.

Screw-in back bolt: divided intotwo-piece back boltsandthree-piece back bolts. A three-piece back bolt consists of a set screw, a back bolt head and a flange nut; a two-piece back bolt consists of a flange shank and a back bolt head. The matching aluminium alloy pendants are mainlyconcave-ear pendants、concave H-type pendantsandC-type pendants, of which the first two are more commonly used.

Comparison dimensionHammer-in back boltScrew-in back bolt
Product compositionshank + sleeve + expansion segment + flat washer + spring washer + hex nuttwo-piece or three-piece
Installation toolsdriving sleeve + hammerhex key/hex wrench + torque drill
Matching pendantsflat-ear, male-and-female (C-type)concave-ear, concave H-type, C-type

VI. How to choose: decision guide

Cases where hammer-in back bolts are preferred:

  • Panel thickness ≥25 mm (mainly stone curtain walls)

  • High construction efficiency and simple installation required

  • Limited ability to control drilling accuracy on site

  • Pursuit of a higher safety factor

Cases where screw-in back bolts are preferred:

  • Panel thickness between 12 and 25 mm (thin panels such as ceramic tiles and vitrified tiles)

  • Brittle panel material requiring stress-free anchoring

  • Strict limits on panel breakage rate

  • Specific applications such as rail transit porcelain plate curtain walls

VII. Frequently asked questions

  • Q: Can hammer-in and screw-in back bolts be used interchangeably?

  • They cannot be directly interchanged. The two types differ in hole dimensions, installation tools and matching pendants. However, if the corresponding holes are reserved at the design stage, both types can be installed.

  • Q: Why do hammer-in back bolts have a higher market share?

  • Hammer-in back bolts account for more than 80% of use in stone curtain walls. The main reasons are: large hole diameter tolerance, simple installation, high safety factor and good cost-effectiveness.

  • Q: What should be done if a screw-in back bolt easily punches through the panel during installation?

  • This requires some experience on the part of the installer to reduce panel breakage. Recommendations: strictly control drilling depth, use hole-gauge tools to check whether the hole depth is acceptable, and control the screwing force during installation.

  • Q: Is there any difference in seismic performance between the two back bolts?

  • Daring hammer-in back bolts have passed a degree-9 rare earthquake seismic test at Tongji University, with acceleration up to 1.24 g. Screw-in back bolts control the expansion dimension through the threaded rod limiting sleeve, resulting in low stress and equally good seismic performance and dynamic load resistance. Both types can meet the requirements of conventional curtain wall projects in terms of seismic performance.

VIII. Summary

Comparison dimensionHammer-in back boltScrew-in back bolt
Installation principleShank stationary, expansion sleeve moves, hammer-driven installationShank rotates, expansion sleeve expands, screw-in installation
Core toolshammer + driving sleevetorque drill + wrench
Applicable panels≥25mm≥12mm
Drilling accuracy requirementLow, large toleranceHigh, strict requirements
Construction difficultySimpleRelatively complex
Matching pendantsflat-ear, male-and-femaleconcave-ear, concave H-type, C-type
Safety factorHigher—
Market shareMore than 80%Mainly used for thin panels

Core selection principles:

  1. Panel thickness determines back bolt type: prefer hammer-in above 25 mm, screw-in for 12-25 mm.

  2. Use hammer-in whenever possible: larger hole tolerance, simpler installation and a higher safety factor.

  3. Thin panels can only use screw-in: thin panels such as ceramic tiles and vitrified tiles are exclusive applications of screw-in back bolts.

  4. Construction accuracy determines success or failure: screw-in back bolts have strict drilling accuracy requirements, so hole diameter and depth must be strictly controlled during construction.

  5. Tools and pendants cannot be mixed: the two back bolt types use different installation tools and pendants; confirm both during selection.

Daring offers the full range of hammer-in and screw-in back bolts in M6 and M8, with dedicated drilling machines and 6063-T6 aluminium alloy pendants. For back bolt selection advice for specific projects, please consult the Daring technical team.

References:

1. Daring website— installation technique of hammer-in back bolts

2. Daring website— installation technique of screw-in back bolts

3. Daring website— hammer-in back bolt product page

4. Daring website— screw-in back bolt product page

5. Installation techniques for stone back bolts and three common back bolt methods (general industry knowledge)

6. Classification of back bolts and comparison of advantages and disadvantages (general industry knowledge)

7. In-depth explanation of four types of stone back bolts (general industry knowledge)

Back to Daring Home  Back to Top