Product Knowledge

A look at the never-implemented JGJ133-2013 back bolt standard

Views: 0Posted on: 2019-03-04

People in the industry may know that JGJ 133-2013 Technical Specification for Metal and Stone Curtain Wall Engineering currently exists only as a draft for approval,and has not actually taken effectThis is a code for back bolts in the true sense, and perhaps the most comprehensive national code evaluating back-bolted stone curtain walls that has appeared to date.

Here, we will talk about the provisions related to back-bolted dry-hung stone curtain walls. Because the text quotes code content many times, it is rather long (about 3,150 words in total); please read through patiently.

About the materials of stone curtain walls

The general provisions and Section 3.4 of the code state the following:

When the curtain wall height exceeds 100m, granite shall be used.

3.4.1 Stone curtain wall panels should use granite panels suited to their functional purposes.

3.4.7 The thickness, water absorption, and single panel area of curtain wall stone panels shall comply with Table 3.4.7. For flame-treated panels and slabs with naturally rough surfaces, the minimum thickness shall be increased by 3mm over the values in Table 3.4.7.

Table 3.4.7 Requirements for the thickness, water absorption, and single panel area of stone panels

Stone type

Granite

Other types of stone

frk(N/mm²)

≥8.0

≥8.0

8.0>frk≥4.0

Thickness t (mm)

≥25

≥35

≥40

Water absorption (%)

≤0.6

≤5

≤5

Single panel area (m²)

Should not exceed 1.5

Should not exceed 1.5

Should not exceed 1.5

3.4.8 When the curtain wall height exceeds 100m, the average value of the flexural strength test of granite panels shall not be less than 12.0, the characteristic value shall not be less than 10.0, and the thickness shall not be less than 30mm.

Because granite is fairly hard (Mohs hardness of about 6-7), is produced in large quantities, is inexpensive, and is chemically more stable, it is the first choice for stone curtain walls. For curtain walls over 100m high, dry-hung granite 30mm thick or more is safer relative to other stones. Moreover, the most intuitive thickness and single panel area mentioned above can serve as a reference; if the values in the table are met, a properly installed curtain wall project will be quite safe.

The author has encountered some high-end projects that, in pursuit of artistic effect, used soft thin panels (generally no more than 25mm thick) such as travertine and carved sandstone, or even oversized panel surfaces, which is not very friendly to the installation of stone curtain walls. However, once a project's design is completed, it is hard to change, and choosing suitable back bolts can raise the overall safety level of the curtain wall by one grade.

About the installation, processing, and maintenance of stone curtain walls

For panels requiring special installation methods or the installation of special panels, there are the following provisions:

4.5.1 Overhanging stone panels should be connected with back bolts, and penetrating metal pendants or metal frames should be provided; the back of the panel should be surface-treated to enhance overall integrity.

4.5.3 Decorative lines protruding from the curtain wall surface should be connected with back bolts or long bolts.

For overhanging stone installation, the back bolt hanging method offers higher safety, and decorative lines can also be connected with back bolts. Moreover, panels made of non-granite materials should also be installed with back bolts as much as possible because of their insufficient hardness; the relevant provision is as follows:

6.1.1 Panels shall be reliably connected to the supporting structure; for panels of non-granite stone and granite panels on curtain walls over 100m high, connection with back bolts is recommended.

In addition, the code makes the following suggestions on the layout and installation positions of stone holes:

6.5.3 The distance from the back bolt centerline to the edge of the stone panel should not be greater than 300mm, nor less than 50mm;spacing materials such as nylon should be used between the back bolt and the back bolt hole to prevent hard contact;the distance between back bolts should not be greater than 1200mm, and should meet the following requirements (Figure 6.5.3).

lx/5≤bx and bx≤lx/4 (6.5.3-1)

ly/5≤by and by≤ly/4 (6.5.3-2)

Figure 6.5.3 Back bolt edge distance

It is worth mentioning that the above requires that spacing materials such as nylon may be used between the back bolt and the back bolt hole to prevent hard contact. As a manufacturer, the author does not agree with this statement. On the one hand, spacing materials may increase stress; on the other hand, the fire resistance and corrosion resistance of spacing materials may not be good, and using them will reduce the safety of the stone curtain wall to a certain extent.

About curtain wall maintenance, it is easier to understand: inspect regularly, and repair or replace in time when needed, as follows:

11.2.1-6 When the back bolts of a stone curtain wall become loose or fall off, they should be repaired or replaced in time.

About the requirements for back bolts

The smallest anchoring structural component in a back-bolted stone curtain wall is the back bolt itself. A few back bolts must bear the weight of the entire panel and the wind load, so there are naturally rather strict requirements:

6.5.2-1 The performance of back bolts shall comply with the current national standard Mechanical Properties of Fasteners Stainless Steel Bolts, Screws and Studs GB/T 3098.6, and the material should be austenitic stainless steel of group A4 or higher. The back bolt diameter should not be less than 6mm and shall not be less than 4mm.

6.5.6 The design value of the load capacity of the bolt shall be its characteristic value of load capacity divided by a factor of not less than 2.15.

The above states that the back bolt diameter shall not be less than 4mm. I think this sentence is redundant for today's industry standards, because back bolts basically come only in M6 and M8.The above states that the back bolt material should be A4 stainless steel, consistent with the requirement of 6.5.2 in the explanatory notes, butin practice, A2 stainless steel back bolts are actually used more often in non-harsh environments, simply because A2 back bolts are cheaper. This is understandable, but the bizarre thing is that some projects directly use back bolts made of grade 201 material or iron for dry hanging; their corrosion resistance and safety are worrying.

For how back bolt holes are processed, the following passage gives detailed requirements. This is the key point of back-bolted stone curtain walls and plays a decisive role in back bolt installation:

8.5.5 The processing of stone slabs connected with back bolts shall meet the following requirements:

1 The allowable deviation of back bolt diameter is ±0.4 mm, the allowable deviation of length is ±1.0 mm, and the straightness tolerance is 1 mm;

2 The rod diameter of the back bolt shall not be less than 6.0 mm.The anchoring depth should not be less than 1/2 of the stone thickness, nor more than 2/3 of the stone thickness;

3 Back bolt holes should be formed with special drilling machines and checked with special hole gauges; the allowable deviations of back bolt holes shall meet the requirements of Table 6.5.3-1;

Table 8.5.5 Allowable deviations of back bolt hole processing (mm)

Item

Straight hole

Undercut

Hole position

Hole spacing

Distance from hole position to short edge

Diameter

Hole depth

Diameter

Hole depth

Allowable deviation

+0.4

-0.2

±0.3

±0.3

±0.2

±0.5

±1.0

Minimum 50

4 The connection between the back bolt and the panel for curtain wall stone shall be firm and reliable, and the installation method and tightening torque of back bolts shall comply with the requirements of the back bolt manufacturer;

Here the anchoring depth of back bolts is introduced,and before this code, no national code had specified the anchoring depth that back bolts should have, but such requirements had long been a requirement of back bolt manufacturers. Some local codes have also mentioned the anchoring depth of back bolts, but many of the statements are inaccurate. For example, DGJ08-56-2012 Shanghai Technical Specification for Building Curtain Wall Engineering mentions that the minimum embedment depth of back bolts should not be less than 15mm and that the embedment depth should be 2/3 of the panel thickness. Such statements cannot hold up in the industry,and more constructors choose 1/2 of the panel thickness as the embedment depth of the back bolt. As for the tolerances of back bolts, I think they cannot be judged simply by the data given in the table. There are many back bolt manufacturers, and the dimensions of each manufacturer's back bolts differ to some extent; only with good tolerance fit can qualified back bolt holes be drilled. After drilling back bolt holes, special tools should be used for sampling inspection of the holes.

The explanatory notes of this code also contain some content about back bolts, such as the selection of back bolt materials, the number of back bolts per panel, and back bolt installation methods, roughly as follows:

6.5.2 As fasteners for curtain walls, back bolts shall be made of stainless steel with higher requirements than ordinary stainless steel. The current national standard Mechanical Properties of Fasteners Stainless Steel Bolts, Screws and Studs GB/T 3098.6 points out that group A2 steel is not suitable for non-oxidizing acids and media containing chlorine, while group A4 steel is acid-resistant steel containing molybdenum, with fairly good corrosion resistance. Therefore, curtain wall back bolts, especially those used in coastal areas or environments with a high chloride ion content, should use stainless steel of group A4 or higher.

6.5.4 For back bolt connections, the number of connection points connecting the same piece of stone is usually not less than 3, to ensure reliability and flatness. When the stone panel is small in size, sometimes only 1 or 2 connection points are used; in that case, reliable additional measures should be taken to ensure the safety of the connection, for example, adding nylon push-tight bolts on the inner side of the panel.

8.5.5 For stone slabs connected with back bolts, the processing accuracy requirements for back bolt holes are very high, as they directly relate to the firmness of back bolt fixation; special machines must be used for drilling according to the back bolt specifications.

Natural stone mainly uses press-in expansion or rotation expansion methods to install back bolts. When using the press-in expansion method, special tools should be used to push in and expand the bolt. Back bolts installed by rotation expansion use a torque wrench, where the insertion force forces the expansion segments to open, completing the back bolt installation. During the installation of back bolts, care should be taken to prevent insufficient or excessive expansion; special installation tools or torque wrenches can be used to control installation quality. The torque should be controlled between 70% and 80% of the compressive strength of the stone.

About matching back bolt connectors

Back bolts are used with matching back bolt pendants, which are mostly aluminium alloy pendants; only the framing may use angle steel.

6.5.2-2 The thickness of back bolt connectors should not be less than 3mm; stainless steel listed in Table 5.2.8-1 of this code or aluminium alloy profiles listed in Table 5.2.1 may be used.

The author checked the code and found that 5.2.1 has no table, which is probably one of the problems of this code. The thickness of back bolt pendants should not be less than 3mm; Daring basically uses mature pendants nearly 4mm thick, which provides higher safety. For pendants, installation must also follow the provisions of the code, and their tolerances should be kept within the following ranges:

9.3.6-3 In addition to complying with Table 9.3.4 of this code, the installation deviations of component stone curtain walls shall also comply with Table 9.3.6 for the installation of stone pendants.

Table 9.3.6 Allowable installation deviations of stone curtain wall pendants

Item

Allowable deviation (mm)

Inspection method

Pendant horizontal position

1.0

Level

Pendant elevation

±1.0

Level, spirit level

Front-to-back level height difference of pendants

1.0

Spirit level

Difference between pendant hook centerline and stone slot centerline

2.0

Metal straightedge

Pendant slot insertion depth (compared with design value)

±2.0

Metal straightedge

Distance from pendant hook tip to back bolt centerline

±1.0

Metal straightedge

Depth of pendant insertion (anchoring) into the flange of the supporting rail (compared with design value)

±1.0

Metal straightedge

Summary

This code comprehensively and systematically covers all aspects of back-bolted stone curtain walls, but the author guesses that, because it itself has some minor problems, it failed the review, leaving the back bolt system without a comprehensive and systematic code to govern it. It is hoped that the state can introduce relevant policies more quickly to ensure the safety of back-bolted stone curtain walls. As for the current code, it still has certain reference value for special groups such as designers.



Back to Daring Home  Back to Top