There are thousands of building materials, but basically all of them are governed by corresponding national standards to ensure their quality. Back bolts, as important structural components for dry-hung exterior wall panels, naturally also need to be governed. So what are the standards and codes for back bolts?
Back bolts were introduced from abroad not long ago, only about 20 years, but their appearance has completely changed the decorative forms of exterior walls, and dry-hanging panels with back bolts has greatly improved the overall aesthetics of exterior walls.
Rather embarrassingly, there are relatively few domestic codes involving back bolts; the only current one isGB/T 21086-2007 Building Curtain Wallswhich mentions them briefly, as follows:
5.3.5.3 Metal hanging fixtures
b) Back bolts and butterfly back clamps shall comply with the requirements of relevant standards; material models, dimensions, and mechanical properties shall meet design requirements. The fire resistance, corrosion resistance, and durability of back bolt materials shall be no lower than the corresponding standards of the materials used for the rear support structure, and they shall be made of stainless steel of no lower than grade 316.
7.3.1.3 Stone panels should be processed in the factory; the processing dimensions and allowable deviations of mounting slots and holes shall meet the requirements of Tables 49 and 50.
Table 49 Processing dimensions and allowable deviations of stone panel holes (unit: mm))
Stone panel Fixing method | Hole diameter | Distance from hole centerline to panel edge | Reserved thickness from hole bottom to panel face | Inspection method | |||
Hole category | Allowable deviation | Minimum dimension | Deviation | ||||
Back bolt type | M6 | Straight hole | ﹢0.4 -0.2 | Minimum 50 | 8.0 | -0.4 ﹢0.1 | Caliper Depth gauge |
Undercut | ﹢0.3 Soft stone +1/-0.3 | ||||||
M8 | Straight hole | ﹢0.4 -0.2 | |||||
Undercut | ﹢0.3 Soft stone +1/-0.3 |
7.4.1 Installation deviations of stone panel hanging systems shall comply with Table 51
Table 51 Allowable installation deviations of stone panel hanging systems (unit: mm))
Item | Back clamp | Back bolt | Inspection method |
Hook (slot) centerline deviation | — | ≤2.0 | Steel straightedge |
Hook (slot) elevation | — | ±1.0 | Caliper |
Deviation between back bolt pendant (insert) centerline and hole centerline | — | ≤1.0 | Caliper |
Deviation between back clamp centerline and back clamp groove centerline | ≤1.0 | — | Caliper |
Deviation between the centerlines of the left and right back clamps | ≤3.0 | — | Caliper |
Horizontal deviation of the top edge of stone in the same row | Adjacent panels | ≤1.0 | Spirit level |
Length ≤35m | ≤2.0 | ||
Length ≥35m | ≤3.0 | ||
Vertical deviation of the edge of stone in the same column | Adjacent panels | ≤1.0 | Caliper |
Length ≤35m | ≤2.0 | ||
Length ≥35m | ≤3.0 | ||
Flatness of the stone outer surface | Height difference between adjacent panels | ≤1.0 | Caliper |
Joint width between adjacent stones (compared with design value) | ±1.0 | Caliper |
P.s. The table above is simplified by omitting columns not related to the back bolt series; for the full table, see page 19 of this code.
9.3.1.1 The unit area and thickness of artificial panels shall meet the requirements of Table 61.
Table 61 Dimensional requirements for artificial panels (unit: mm))
Panel category | Thickness/mm | Single panel area/㎡ | Inspection method | |
Porcelain panel | Back bolt type | Other connection methods | ≤1.5 | Caliper |
≥12 | ≥13 | |||
Terracotta panel | ≥15 | — | Caliper | |
Glass-ceramic panel | ≥20 | ≤1.5 | Caliper |
9.3.1.5 The processing dimensions and allowable deviations of glass-ceramic and porcelain panels shall meet the requirements of Table 65.
Table 65 Allowable deviations of hole processing for glass-ceramic and porcelain panels (unit: mm))
Fixing method | Hole diameter Allowable deviation | Undercut diameter Allowable deviation | Anchoring depth | Distance from hole center to panel edge | Reserved thickness from hole bottom to panel face | Inspection Method | |
Minimum value | Allowable deviation | ||||||
Back bolt type | ﹢0.4 0 | ±0.3 | 6 | ±0.2 | Minimum 50 | ≥3.0 | Caliper |
This is the main content about back bolts in the currently effective codes, covering back bolt material requirements, drilling requirements and edge distances, installation deviations, and panel requirements. It can solve most of the problems encountered in practice, but it is still not comprehensive enough.
In addition to national codes, some local codes also give corresponding suggestions and requirements for the use of back bolts, such as the Zhejiang Province code ZJSP16-2013-002 Safety Technical Requirements for Building Curtain Walls (including explanations) 4.1 New Regulations, which can be consulted on your own. However, because it is only a local code with certain regional restrictions, it will not be discussed in detail here.
In fact, a few years ago JGJ 133-2013 Technical Specification for Metal and Stone Curtain Wall Engineering (including explanations) was issued. This code gives a more detailed explanation of stone curtain walls, but it has not been implemented. The author believes that it covers a very wide range, including materials, calculation, acceptance, and many other aspects, so it still has certain reference value.
