If you know the classification and uses of chemical anchors, you know that a chemical anchor is a type of post-installed anchoring material that can be used in many applications such as curtain walls, rail transit, and equipment fixing. During installation, a hole must first be drilled in the concrete; part of the anchor's length is embedded in the concrete and bonded with adhesive, while the exposed portion is used to secure the anchored object.
Standard Embedment Depth of National-Standard Chemical Anchors
At present, the embedment depth of chemical anchors has basically been standardized across the industry; it is shown in table form below:
Table 1. Standard Drill Hole Depth of Chemical Anchors
Chemical Anchor Specification | Standard Hole Diameter | Standard Hole Depth |
M8×110 | 10 | 80 |
M10×130 | 12 | 90 |
M12×160 | 14 | 110 |
M16×190 | 18 | 125 |
M20×260 | 25 | 170 |
M24×300 | 28 | 210 |
M30×380 | 35 | 270 |
If you look carefully, you will find that the industry-standard embedment depth is 8~10 times the outer diameter of the chemical anchor. This is also a fairly practical way of judging whether the embedment depth of a chemical anchor is reasonable.
The standard does not specify a standard embedment depth but does give a minimum embedment depth. JGJ 145-2013, 'Technical Specification for Post-Installed Anchoring in Concrete Structures,' states the following:
7.1.7 The minimum anchoring depth of chemical anchors shall meet the requirements of Table 7.1.7.
Table 7.1.7 Minimum Anchoring Depth of Chemical Anchors
Chemical Anchor Diameter d (mm) | Minimum Anchoring Depth (mm) |
≤10 | 60 |
12 | 70 |
16 | 80 |
20 | 90 |
≥24 | 4d |
The table above can serve as the sole criterion for judging whether the embedment depth of chemical anchors complies with the standard during on-site construction.
Pull-Out Test Results of Anchors at Standard Embedment Depth
In order to better verify the relationship between the anchoring depth and mechanical properties of chemical anchors, we carried out a large number of mechanical property tests. The failure modes of chemical anchors at standard embedment depth when used with chemical cartridges and anchoring adhesive in C30 and C60 non-cracked concrete are as follows:
Figure 2. Failure Modes in Chemical Anchor Pull-Out Tests
Chemical Anchor Specification | With Daring Chemical Cartridge | With Daring Injection Anchoring Adhesive | |||
C30 | C60 | C30 | C60 | ||
M8×110 | Grade 5.8 | △ | △ | △ | △ |
Grade 8.8 | △ | △ | △ | △ | |
M10×130 | Grade 5.8 | △ | △ | △ | △ |
Grade 8.8 | △ | △ | △ | △ | |
M12×160 | Grade 5.8 | △ | △ | △ | △ |
Grade 8.8 | △ | △ | △ | △ | |
M16×190 | Grade 5.8 | △/□ | △ | △ | △ |
Grade 8.8 | □ | △ | □ | △ | |
M20×260 | Grade 5.8 | □ | △ | □ | △ |
Grade 8.8 | □ | △/□ | △/□ | △ | |
M24×300 | Grade 5.8 | / | / | / | △ |
Grade 8.8 | / | / | / | △ | |
M30×380 | Grade 5.8 | / | / | / | △ |
Grade 8.8 | / | / | / | △ |
P.S. In the tables, △ indicates anchor rupture, □ indicates failure at the concrete-adhesive interface, and / indicates not tested.
As can be seen from the tables above,large-size chemical anchors above M16 will be pulled out when pull-out tests are performed with a chemical cartridge, whereas anchors of all specifications will rupture in the threaded rod when pull-out tests are performed with Daring injection anchoring adhesive in C60 non-cracked concrete,This indicateswhen the strength of the adhesive and the concrete is sufficiently high, the threaded rod will rupture in a pull-out test at the standard embedment depth, and at that point the strength of the threaded rod is the weak link of the entire test system.
It is worth mentioning that the load capacity of Daring's chemical anchors can reach first-tier industry levels; at standard embedment depth, their load capacity often exceeds the design value by 3-5 times, so their safety performance is commendable. Taking the M30×380 chemical anchor as an example, its tensile resistance in C60 concrete can reach 480 kN (with rupture of the anchor threaded rod at that point), an impressively high force value.Sometimes increasing the embedment depth only makes construction more difficult without increasing the load capacity — a thankless task.Moreover,for the sake of safety, all Daring chemical anchors of M20 and above are supplied for use with Daring epoxy-based injection anchoring adhesive, not with chemical cartridges.
