Product Knowledge

Hot rolling versus cold forming for cast-in channels: quality differences and purchasing advice

Views: 0Posted on: 2026-09-07

Bottom line:The core difference between hot-rolling and cold-bending processes for cast-in channelslies in forming temperature and microstructure. The hot-rolling process forms the channel by repeated rolling atabove 1200°Chigh temperature; the internal grain structure of the steel is dense and uniform, withno stress concentration, and its mechanical properties and durability are far superior to cold-bent products. The cold-bending process forms the channel by bending atambient temperature, which produceswork hardening and residual stressat the bends; fatigue performance is poor, making it unsuitable for dynamic loads. According toGB/T 37613-2019andTB/T 3329-2013requirements, cast-in channels shall usethe hot-rolling forming process. Daring cast-in channels useQ355 steel formed by single-pass hot rolling, and have passed 2 million fatigue cycles, fire resistance, and other tests, making them the safe choice for metro tunnels, high-speed rail, utility tunnels, and other projects.

In the selection of cast-in channels for projects, the forming process is thecore factordetermining product quality and service life. Many procurement staff and designers lack a deep understanding of the differences between hot rolling and cold bending, often focusing only on price while overlooking the quality risks brought by process differences. This article comprehensively analyzes the differences between hot-rolling and cold-bending processes for cast-in channels from the perspectives of process principles, microstructure, mechanical properties, code requirements, and purchasing advice.

1. Basic understanding of hot-rolling and cold-bending processes

1.1 What is the hot-rolling process

Hot rolling is a process in which steel, at a temperature above itscrystallization temperature (1200°C), is formed by means of dies throughmultiple rolling passes. Its core characteristics include:

  • High-temperature forming: The heating temperature exceeds 1200°C, and the steel is in a recrystallized state

  • Multiple rolling passes: Through multiple passes, the steel is gradually formed into the final cross-sectional shape

  • Right angles at bends: The corners of the cross-section transition zones are filled with generous radii

  • Complex process: High technical barrier and cost much higher than cold bending

1.2 What is the cold-bending process

Cold bending is a process in which a steel plate is bent once into a channel shape atambient temperatureusing a bending machine. Its core characteristics include:

  • Ambient-temperature forming: Formed by mechanical bending at room temperature

  • Single-step bending: The steel plate is bent into a C-shaped channel in one operation

  • Rounded bends: Uniform wall thickness but stress concentration at the bends

  • Simple process: Simple equipment, low technical barrier, and low cost

2. Hot rolling vs. cold bending: a comprehensive multi-dimensional comparison

Comparison dimensionHot-rolling processCold-bending process
Forming temperatureAbove 1200°C (above the recrystallization temperature)Ambient temperature (room temperature)
Forming methodMultiple rolling passes with diesSingle bending operation with a bending machine
Shape at bendsRight angles, with well-filled corner radiiRounded
Wall thickness characteristicCan be locally thickened to optimize cross-section load distributionUniform wall thickness throughout, with a small section modulus
MicrostructureIsotropic, with no stress concentrationWork hardening and residual tensile stress
Fatigue performanceExcellent, capable of withstanding 2 million load cyclesPoor, unsuitable for dynamic loads
Stiffness and torsional resistanceHigh, with strong local load-bearing capacityLower stiffness and weak torsional resistance
PlasticityHigh, with good toughness and ductilityLimited by work hardening
Production costHigh (complex process, high technical barrier)Low (simple equipment, low barrier)

3. In-depth analysis of the core differences

3.1 Microstructural difference: isotropy vs. stress concentration

The most fundamental difference between the two processes lies in theinternal microstructure of the steel. Hot rolling takes place in a high-temperature recrystallized state, reshaping the metallic grain structure of the steel to reach a condition ofisotropy, density, and uniformity, andthere is no stress concentration problem.。

Cold bending forms the channel at ambient temperature, producingsevere work hardening and residual tensile stress. Under long-term dynamic loads, these residual stresses may causestress corrosion cracking, leading to premature product failure.

3.2 Mechanical property differences: hot rolling leads across the board

For cast-in channels formed by hot rolling, theirmechanical properties are far superior to those of cold-formed products. Specifically:

  • Fatigue performance: Hot-rolled channels can withstand2 millionload cycles, while cold-formed channels have poor fatigue performance andare unsuitable for dynamic loads

  • Dynamic load-bearing capacity: Hot-rolled steel channels have high capacity under dynamic loads, while cold-formed steel channels have lower stiffness and weaker torsional and localized concentrated-load capacity

  • Plasticity: Hot-rolled steel channels have high plasticity, good toughness, and good ductility

3.3 Mandatory code requirement: hot rolling is the only compliant choice

According to a number of national and industry standards, cast-in channelsshall be formed by the hot-rolling process:

  • GB/T 37613-2019, Section Steel for Cast-in ChannelsClause 6 explicitly stipulates:the hot-rolling forming process shall be used, and stress relief is required after welding

  • TB/T 3329-2013, Cast-in Channels for Catenary in Electrified Railway Tunnelsstipulates that cast-in channelsshall be hot-rolled channels, with Q355B material

This means that in formal projects such as rail transit and metro tunnels,cast-in channels produced by cold bending do not comply with code requirementsand cannot pass acceptance inspection.

4. Purchasing decision guide

4.1 When hot-rolled cast-in channels should be preferred

  • Rail transit projects: Metro tunnels, high-speed rail catenary, utility tunnels, and others, where codes mandate hot rolling

  • Applications subject to dynamic loads: Under cyclic loads such as train vibration and wind-induced vibration, hot-rolled channels offer excellent fatigue performance

  • Projects with extremely high safety requirements: Nuclear power, bridges, supertall curtain walls, and others

  • Projects pursuing long-term durability: Hot-rolled products have no stress concentration and a service life far superior to cold-formed products

4.2 Beware of the low-price trap of cold-formed products

Some low-priced cold-formed cast-in channels on the market may look smooth and dimensionally accurate, but internally they harborstress concentration and residual stressrisks. Under long-term use or dynamic loads, they are prone tofatigue failure, posing serious safety risks.

When purchasing, focus on the following:

  • Product test reports: Whether they are complete and carry CMA/CNAS accreditation

  • Material: Whether it is Q355B or 304/316 stainless steel

  • Fatigue testing: Whether it has passed 2 million fatigue cycle testing

  • Corrosion protection process: Whether the hot-dip galvanized coating thickness is ≥80 μm

5. Daring hot-rolled cast-in channels — the code-compliant choice with guaranteed quality

5.1 Core product advantages

Daring cast-in channels are made ofQ355 steel formed by single-pass hot rolling, manufactured strictly in accordance with GB/T 37613-2019 and TB/T 3329-2013. The products have the following core advantages:

  • Reliable material: Q355 steel or 304/316 stainless steel, with mechanical properties meeting code requirements

  • Compliant process: Single-pass hot rolling, no stress concentration, and excellent mechanical properties

  • Comprehensive testing: Passed2 million fatigue cycles, fire resistance, and other tests

  • Corrosion protection and durability: Hot-dip galvanized coating thickness ≥80 μm, meeting the 1,200-hour salt spray test requirement

  • Versatile processes: Both welded and riveted connection processes are available

5.2 Application scenarios

Daring hot-rolled cast-in channels are widely used in:

  • Metro tunnels: Catenary suspension, pipe supports, and equipment fixing

  • Urban utility tunnels: Pipe supports and mechanical and electrical equipment installation

  • High-speed rail projects: Embedment of catenary foundations in tunnels

  • Building curtain walls: Curtain wall sub-frame connections

6. FAQ

Q1Which is better for cast-in channels: hot rolling or cold bending?
Hot rolling is better. Hot-rolled products have no internal stress concentration, excellent fatigue performance, and mechanical properties far superior to cold-formed products. Both GB/T 37613-2019 and TB/T 3329-2013 explicitly stipulate that cast-in channels shall be formed by hot rolling.
Q2Why can't cold-formed cast-in channels be used?
Cold bending produces work hardening and residual tensile stress at the bends, resulting in poor fatigue performance and unsuitability for dynamic loads. Under long-term dynamic loads it may cause stress corrosion cracking, and it does not comply with code requirements.
Q3Why do hot-rolled cast-in channels cost more?
Hot rolling is a complex process with a high technical barrier, requiring multiple rolling passes at temperatures above 1200°C. Although the initial cost is higher, the excellent performance and very long service life are worth it.
Q4What process does Daring use for its cast-in channels?
Daring cast-in channels are made of Q355 steel formed by single-pass hot rolling, manufactured strictly in accordance with GB/T 37613-2019 and TB/T 3329-2013, and have passed 2 million fatigue cycles, fire resistance, and other tests.
Q5How can you tell whether a cast-in channel is hot-rolled or cold-formed?
First, look at the bends: hot-rolled channels have right angles, cold-formed ones have rounded bends. Second, look at wall thickness: hot-rolled channels can be locally thickened, while cold-formed ones have uniform thickness. Third, check the test report: hot-rolled products should have passed 2 million fatigue cycle testing. Fourth, check the material: hot-rolled products mostly use Q355B.

Daring cast-in channels are made ofQ355 steel formed by single-pass hot rolling, manufactured in strict accordance with GB/T 37613-2019 and TB/T 3329-2013, having passed 2 million fatigue cycles, fire resistance, and other tests. Materials cover Q355 steel and 304/316 stainless steel, with both welded and riveted processes available. For advice on selecting hot-rolled cast-in channels for a specific project, please contact Daring's technical team.

References

Daring website — Cast-in channels product series

GB/T 37613-2019, Section Steel for Cast-in Channels — hot-rolling process requirements

TB/T 3329-2013, Cast-in Channels for Catenary in Electrified Railway Tunnels — provisions for hot-rolled channels

GB/T 1591-2018, High-Strength Low-Alloy Structural Steels — Q355 material requirements

GB/T 13912-2020, Metallic Coatings — Hot-Dip Galvanized Coatings on Fabricated Iron and Steel Articles — Specifications and Test Methods

Back to Daring Home  Back to Top